LAWO Crystal standard configuration Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 149

background image

crystal standard configuration User Manual

Version: 6.4.0/4

93/149

8. Operation

8.9.3

The METERING Page

Other signals can be metered by pressing the

METERING

button (on the DOCK):

DisplayDock Metering page

The page is divided into two rows to meter outputs (at the top) and inputs (at the bottom). All of the PPMs are
dynamic Peak Program Meters and use a digital scale relative to 0dBFS. The output meters include momentary
loudness metering (as described

).

Output Metering

On the top row are meters for the summing buses:

PGM 1

,

PGM 2

,

PGM 3

and

AUX 1

. Note that a dedicated

meter for

AUX 2

is not available but it can be metered on the follow MONITOR meter by selecting the AUX as

the CR monitor source.

The

MISC

meter is switched using the on-screen "N-1" buttons. It can meter any of the N-1 outputs: for Hybrid

1&2, RAVENNA Codec 1 to 4 or the AES Codec.

Input Metering

On the bottom row are 8 meters which are switched using the on-screen "Fader" buttons. This allows you to
meter up to 24 faders (for a maximum size surface).

«
...
91
92
93
94
95
...
»

Содержание Crystal standard configuration






















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Crystal standard configuration

Бренд: Balanced Body Страницы: 4

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

KOMPAN SPF28666S

Бренд: Bommelland Страницы: 23

Бренд: MacDon Страницы: 2

Бренд: MacDon Страницы: 214

Бренд: MacDon Страницы: 32

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

ULTRATHERM 908i

Бренд: gbo Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды