LAWO Crystal standard configuration Скачать руководство пользователя страница 87

Страница: 87 / 149

crystal standard configuration User Manual

Version: 6.4.0/4

87/149

8. Operation

8.8.6

Limiter

Aseparate limiter is available for all MIC sources and some of the other sources.

To check if the limiter is supported, press the source's

ACCESS

key and then look at DisplayDock - if the

Limiter graphs (and parameters) appear, then the DSP is available. Alternatively, look at the Central Module:

LIM

key lit = limiter available.

To access the limiter parameters, press an

ACCESS

key followed by

LIM

on the Central Module.

Surface Controls (Limiter)

DisplayDock

The following parameters are available for the Limiter:

LIM

- on/off for the limiter: red = on.

THRS

- threshold from -93dB to +27dB.

RLS -

release time from 10ms to 5000ms.

The Limiter graph on DisplayDock includes a green ball which represents the output level of the Limiter.
This changes dynamically as the signal level varies, and so is extremely helpful when adjusting parameters.

8.8.7

Delay

Delay is not supported by any source in the crystal standard configuration. Therefore, the

DLY

key on the

Central Module has no function.

Содержание Crystal standard configuration






















































































































































Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды

LAWO Crystal standard configuration, Руководство пользователя

Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды