background image

crystal standard configuration User Manual

Version: 6.4.0/4

92/149

8. Operation

8.9.2

Loudness Metering (for PGM 1)

DisplayDock (Monitoring & Metering)

On DisplayDock, there are two loudness measurements: momentary and integrated which conform to the ITU-R
BS1770.

Momentary Loudness (Bargraph)

The  blue  bargraph  represents  the  average  energy  of  the  summed  component  channels:  left  and  right.  The
average  is  measured  using  either  a  Momentary  (400ms  sliding  window)  or  Short  term  (3s  sliding  window)
integration time.

The color indicates whether loudness is above or below the Target Level:

·

Light Blue

 = equal to, or below, the Target Level.

·

Dark Blue

 = above the Target Level.

Scale markers indicate a tolerance of +/- 1 LU/LK.

Integrated Loudness Measurement (in LUFS)

The integrated loudness measurement is controlled by the on-screen 

Start

,

 Stop 

and 

Reset

 buttons. It is very

useful for measuring loudness over a longer period - for example, for the duration of the show.

The measurement is displayed in LUFS (Loudness Units Full Scale).

Содержание Crystal standard configuration






















































































































































Отзывы: