manualshive.com logo in svg

LAWO Crystal standard configuration, Руководство пользователя, Страница: 12 / 149

Поделиться
Скачать
LAWO Crystal standard configuration Скачать руководство пользователя страница 12

crystal standard configuration User Manual

Version: 6.4.0/4

12/149

4. The Hardware

4.3.2

Rear View

 9 

  Analog & Digital IO

The following audio connections are always included.

·

HEADPHONE 1 & HEADPHONE 2 - two stereo headphone outputs.

·

LINE OUTPUT - 8 x line level outputs.

·

MIC/LINE INPUT - 4 x mic/line in + 4 x line level in.

·

AES3 INPUT - 4 x AES3 inputs.

·

AES3 OUTPUT - 4 x AES3 outputs.

 10 

  GPIO

This connector provides 8 x GPI (optocouplers) and 8 x GPO  (silent  and  self-healing  relays)  for  local  signaling
and switched functions.

 11 

  WCLK IN & OUT

 

WCLK IN can be used to connect an external sync reference. The sync reference options are MADI, WCLK IN,
AES3 or Internal.

WCLK OUT always provides an output of the current system reference.

 12 

  CASE

The CASE grounding screw should be used to ground the frame.

 13 

  12V DC & AC MAINS Inputs

Every device comes with dual power feeds: AC and DC. To use the DC input, you will need the external 12V DC
power supply. This is optional and must be ordered separately.

If both inputs are connected, then the two feeds provide main and redundant power.

The Compact Engine 

MUST

 be connected to the mains using the power cable supplied with the system.

Содержание Crystal standard configuration






















































































































































Отзывы:

Нет отзывов