LAWO Crystal standard configuration Скачать руководство пользователя страница 88

Страница: 88 / 149

crystal standard configuration User Manual

Version: 6.4.0/4

88/149

8. Operation

8.8.8

EQ parameters are available for all four MIC sources and some of the other sources.

To check if EQ is supported, press the source's

ACCESS

key and then look at DisplayDock - if the EQ graph

(and parameters) appear, then the DSP is available. Alternatively, look at the Central Module:

key lit =

dynamics available.

The EQ provides a 3-band parametric EQ plus high-pass and low-pass filters. The filters can be used either as
fixed slope filters (12dB per octave) or shelving EQ.

To access the EQ parameters, press an

ACCESS

key followed by

on the Central Module.

The fader strip controls update to show the last page adjusted - in our example, the 3-band equalizer:

Surface Controls (3-band EQ)

DisplayDock

Press down on the left (master) rotary control to access the second page (for the 2-band Filters).

Press again to return to the 3-band parametric EQ (page 1).

The EQ graph on DisplayDock shows all five bands of EQ simultaneously. This provides a great overview of
the complete section.

Содержание Crystal standard configuration






















































































































































Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды

LAWO Crystal standard configuration, Руководство пользователя

Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды