LAWO Crystal standard configuration Скачать руководство пользователя страница 39

Страница: 39 / 149

crystal standard configuration User Manual

Version: 6.4.0/4

39/149

7. System Setup

Once a valid network connection is detected, the program begins checking the "Firmware" and

"Config" status of the device - this may take a few seconds.

If either component has a new version, then start by updating the firmware and then transferring the
configuration. You should perform both of these tasks

before

updating

the RAVENNA IO card.

Checking Firmware

Firmware Up to Date

7.4.2

Updating the Firmware

If a new "Firmware" version is

available

, then update the Compact Engine as follows.

Click on

Update

to start the update procedure.

The "Firmware" status message shows

update in progress

while the necessary data is transferred. This may

take a while.

Following the transfer, the Compact Engine restarts and during this time you will lose the network

connection ("Connection Status" =

NOT connected

After the restart, the program reconnects and checks the "Firmware" and "Config" statuses again.

The "Firmware" status should now be

up to date

and you can continue on to the configuration.

Содержание Crystal standard configuration






















































































































































Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды

LAWO Crystal standard configuration, Руководство пользователя

Результаты поиска

Содержание Crystal standard configuration

Отзывы:

Похожие инструкции для Crystal standard configuration

Бренды по названию

Популярные бренды