Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 34

Страница: 34 / 76

3-2

F-1097-2305

OPERATION

TABLE OF CONTENTS

Tractor Preparation

The Brillion Till 'N Seed is available as a Pull-Type Hitch
or 3-PT Hitch version.
•

A Pull Type seeder is equipped to be pulled by a
tractor with a drawbar, no clevis.

•

A 3-PT mounted seeder is compatible with Category
2 or 3 Free Link, Category 2, 3N or 3 Quick Hitch
Coupler.

Tractor Preparation for Attaching

3-PT Hitch Till 'N Seed

1. The Brillion Till 'N Seed is designed to be pulled with

Category 2 or 3 Free Link, and Category 2, 3N, or 3
Quick Hitch Coupler.

See Figure 3-1.

Be sure

Tractor's Hitch Capacity is not exceeded by the Laden
Mass of the Seeder.

Refer to Tractor Operator's

Manual.

2. Be sure Tractor is properly ballasted. A minimum 25%

of Tractor and Equipment Laden Mass must be on
Tractor Front Wheels in transport position to maintain
stability. Calculate the Loaded Seeder Mass.

See

“Specifications” in Chapter 5.

(Seeder weight plus

the seed box capacity with desired seed.)

Refer to

Tractor Operator's Manual.

3. Check the Tractor tire inflation levels to ensure that

they are properly inflated for the additional Laden
Seeder Mass.

Refer to the Tractor Operator's

Manual.

Be sure not to over ballast and exceed

Tractor Tire Capacity.

4. Set Tractor 3-PT Lower Links to allow lateral

(torsional) float.

Refer to Tractor Operator's

Manual.

If left rigid, the Brillion Till 'N Seed may not

follow ground contours resulting in poor germination.

5. Set Lift Rod length long enough to ensure Seeder can

float downward in the case of a furrow or waterway.
Lower Links should be the same height, leveling the
Brillion Till 'N Seed side to side. Fine adjustments may
need to be made after hookup is completed.

Refer to

the Tractor Operator's Manual.

6. Attach the Till 'N Seed to the Tractor's 3-PT Free Link

or Quick Hitch Coupler using the appropriate size pins
and bushings. Be sure to use the hardware provided
and is in good working order.

See Figure 3-1.

7. Refer to the Tractor Operator's Manual for Quick

Hitch Coupler Operation.

DANGER

8. Connect the 7-Pin Connector to Tractor Outlet,

routing cable by avoiding pinch points.
• Make sure the tractor has a good clean

receptacle, free of dirt and corrosion.

• Make sure the 7-Pin Connector is inserted ALL

the way in. With tighter fitting pins, operator may
think the Connector is all the way in, but really
isn’t.

• Make sure the tractor receptacle cover latches

over the keyway on the 7-Pin Connector to hold
the Connector in place.

• If an operator plugs in the 7-Pin Connector, but

the lights do not seem to work right, check the
above items to make sure there is a good
connection with the 7-Pin Connector.

9. Raise the Till 'N Seed. Remove Rear Roller Locking

Pins from both sides and place them in the Toolbox.
Raise Parking Stands, both sides.

See Figures 3-2

and 3-3.

Adjust or lock tractor sway stabilizers if

equipped, centering the Seeder with the Tractor.

Refer to the Tractor Operator’s Manual.

10. Lower the Till 'N Seed, if necessary level Seeder side

to side (laterally) by adjusting Lift Rod length. Level
Seeder front to back by adjusting the Tractor Upper
Link length as required.

Refer to the Tractor

Operator’s Manual.

Do not allow any bystanders to stand between the
tractor and the machine while backing up to the
machine.

Содержание Brilllion Till'N Seed BPSB-8













































































Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды

Landoll Brilllion Till'N Seed BPSB-8, Руководство оператора

Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды