Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 76

background image

4-14

F-1097-2305

MAINTENANCE

TABLE OF CONTENTS

Seed Meter Adjustment

IMPORTANT

All the Seed Meters MUST BE CLOSED! It may be
necessary to individually adjust Seed Meter Cups.

All Seed Meters must be set the same to ensure uniform
seeding. To check, set the Seed Rate Adjusting Nut to
0-A. The “A” on the Seed Rate Adjusting Nut is
positioned over the “0” (the nut covers half of the “0”) and
snug against the Bearing.

See Figures 4-16 and 4-17.

Figure 4-16: Micro-Meter Seed Box Rate Adjuster

Figure 4-17: Large Meter Seed Box Rate Adjuster

All Seed Meters should be closed. Seed Meter Feed
Shutoff against Seed Meter Cup Star Washer in Seed
Meter Cup.

See Figure 4-18.

If not, there are two

adjustments to make as needed.

IMPORTANT

Ensure that the Seed Shaft can turn freely without
any binding when the Seed Meters are open or
closed after servicing. Seed Box with Large Seed
Meters you may need to make adjustments to the
Seed Meter Supports at each Seed Meter Cup. See
Figure 4-19.

Figure 4-18: Seed Meter Feed Shutoff

Figure 4-19: Seed Meter Supports

1.

Micro-Meter Box:

Hex Collar with Set Screws on

both ends of the Adjusting Screw are used to adjust
all Seed Meters the same amount.

See Figure 4-16.

To adjust Seed Meters to be closed at "0A", loosen
Hex Collars with Set Screws (remove set screws first)
and set Adjusting Screw to "0A". Slide Seed Shaft to
close all Seed Meters. Tighten Hex Collars with Set
Screws against Adjusting Screw and install set
screws to lock against Seed Shaft flats.

Once

adjusted

DO NOT

loosen or adjust the Hex Collars.

2.

Large Meter Box:

1/2-13 Locknuts on both ends of

the Adjusting Screw are used to adjust all Seed
Meters the same amount.

See Figure 4-17.

To adjust

Seed Meters to be closed at “0A”, loosen 1/2-13
Locknuts and set Adjusting Screw to “0A”. Slide Seed
Shaft to close all Seed Meters. Tighten 1/2-13
Locknuts against Adjusting Screw.

Once adjusted

DO

NOT

loosen or adjust the 1/2-13 Locknuts.

Pinwheel

Seed Rate

Adjusting Nut

1-8 Nut

Adjusting

Screw

Bearing

"0"

Seed Shaft

Micro-Meter

Hex Collar

Hex Collar

Seed Shaft

Seed Rate

Adjusting Nut

Pinwheel

1/2-13 Locknut

1-8 Nut

"0"

Bearing

Adjusting

Screw

Large Meter

1/2-13 Locknut

Seed Meter Cup

Star Washer

Feed Shutoff

Feed Roll

Seed Meter

Cup

Seed Meter

Cup

Flange Bolt

Seed Meter Support

«
...
64
65
66
67
68
...
»

Содержание Brilllion Till'N Seed BPSB-8













































































Отзывы:

Нет отзывов

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренд: Taylor Made Страницы: 2

Бренд: York Fitness Страницы: 18

Бренд: Safco Страницы: 2

Бренд: Omni Страницы: 193

Бренд: parr Страницы: 20

Бренд: Landoll Страницы: 71

Бренд: York Fitness Страницы: 4

Бренд: W&H Страницы: 23

Бренд: Bartscher Страницы: 24

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: TEC Страницы: 6

Бренд: U Technology Страницы: 6

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Fresh DFG58D1BSS

Бренд: Danby Страницы: 11

SimNewB Anomaly Set

Бренд: laerdal Страницы: 10

Бренд: Biosonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды