Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 76

background image

3-8

F-1097-2305

OPERATION

TABLE OF CONTENTS

Micro-Meter and Large Meter

Box - Seed Rate Adjustment

WARNING

NOTE

To avoid Seed Meter damage, if there is seed in the
meters, decrease rate in small increments. Decrease rate
no more than one nut revolution and rotate Seed Shaft to
purge seed from meters. Continue adjustment as needed.

Before filling with seed be sure Seed Shaft turns freely
and Seed Meters are free of any foreign matter.

Wrenches for adjustment and the Calibration Crank
Assembly are stored in the toolbox.

See Figure 3-12.

Figure 3-12: Adjustment Wrenches

Seed Rate Charts specific to the Seed Metering System
are located inside the Seed Box Cover and in this manual.

See Figures 3-19

It should be used as a general guide only. Because of
seed variation, a more accurate rate can be determined
by performing a seed rate calibration for that specific
Seed Box.

See “Micro-Meter Box Calibration for

Unlisted Seeds” on page 3-9

and “Large Meter Box

Calibration for Unlisted Seeds” on page 3-11.

On the right side, the Seed Rate for the Seed Meters can
be set by adjusting the Seed Rate Adjusting Nut and
Adjusting Screw.

See Figures 3-13 and 3-14.

Figure 3-13: Micro-Meter Box Seed Rate Adjustment

Figure 3-14: Large Meter Box Seed Rate Adjustment

IMPORTANT

DO NOT Loosen or Adjust the Hex Collar and the
1/2-13 Locknut . See Figures 3-13 and 3-14.

1. To

increase

the rate of seeding, loosen the 1-8 Nut

and Seed Rate Adjusting Nut with the supplied
wrenches. Back the 1-8 Nut away from the Bearing.
Set the Seed Rate Adjusting Nut appropriate letter
with the Adjusting Screw corresponding number for
the desired Seed Rate. Tighten the 1-8 Nut up to the
Bearing.

2. To

decrease

the rate of seeding, loosen the 1-8 Nut

and Seed Rate Adjusting Nut with supplied wrenches.
Set the Seed Rate Adjusting Nut appropriate letter
with the Adjusting Screw corresponding number for
the desired Seed Rate. Tighten the 1-8 Nut up to the
Bearing.

Seed Meters discharge to the front of the machine to aid
the operator in determining proper operation. Pinwheels
on the RH end of the Seed Shafts aid the operator in
identifying Seed Shaft rotation.

• To prevent damage to the seed meters, Do not

apply excessive force to the adjusting nuts.
Failure to do so may result in the seed being
pinched between the cut-off and washer inside
the seed cup.

• Do not close the meters more than 1/8" when

there is seed in the meters without rotating the
seed shaft. This prevents damage to the rotating
washers and retainer rings in the seed meters.

• Do not attempt to open meters more than 1".

(Feed rolls could become disengaged from
washer in the seed cup.)

Claibration Crank

Assembly

Toolbox

Wrench

Pinwheel

Seed Rate

Adjusting Nut

1-8 Nut

Adjusting

Screw

Bearing

"0"

Seed Shaft

Micro-Meter

DO NOT

Loosen or Adjust

Hex Collar

DO NOT

Loosen or Adjust

Hex Collar

Seed Shaft

Seed Rate

Adjusting Nut

Pinwheel

DO NOT

Loosen or Adjust

1/2-13 Locknut

1-8 Nut

"0"

Bearing

Adjusting

Screw

Large Meter

DO NOT

Loosen or Adjust

1/2-13 Locknut

«
...
38
39
40
41
42
...
»

Содержание Brilllion Till'N Seed BPSB-8













































































Отзывы:

Нет отзывов

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренд: Rath Страницы: 3

Бренд: Sagola Страницы: 8

Бренд: Parata Страницы: 40

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: Landoll Страницы: 34

Бренд: Makita Страницы: 10

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: Zimmer Страницы: 2

Бренд: ZipRip Страницы: 31

Бренд: ABB Страницы: 4

Бренд: Daikin Страницы: 12

Бренд: Napoleon Страницы: 3

Бренд: Daikin Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды