Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 56

Страница: 56 / 76

4-4

F-1097-2305

MAINTENANCE

TABLE OF CONTENTS

Lubrication

The Till 'N Seed is equipped with maintenance free
Bearings. These areas require no lubrication.
•

Grease Lift Wheel Hubs and Gauge Wheel Hubs
every 50 hrs.

See Figure 4-3.

•

Grease Rockshaft Bearings every 8 hrs.

See

Figure 4-3.

•

Oil #80-2 Roller Chain immediately after each use
while chain is still warm for best penetration.

See

Figure 4-4.

•

Oil #40 and #60 Roller Chains periodically.

See

Figure 4-4.

•

When the Machine is not used for some time,
exposed portions of the Hydraulic Cylinder Rods must
be cleaned and covered with a thick coat of grease to
prevent corrosion, which will damage the seals.

Figure 4-3: Lubrication Maintenance

Hrs

Wheel Hub

Repack Annually

Lift Tire and Wheel

Assembly

Hrs

Rockshaft

Bearing

Rockshaft

Hrs

Gauge Wheel

Tire and Wheel

Assembly

Wheel Hub

Repack Annually

Содержание Brilllion Till'N Seed BPSB-8













































































Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды

Landoll Brilllion Till'N Seed BPSB-8, Руководство оператора

Результаты поиска

Содержание Brilllion Till'N Seed BPSB-8

Отзывы:

Похожие инструкции для Brilllion Till'N Seed BPSB-8

Бренды по названию

Популярные бренды