Landoll Brilllion Till'N Seed BPSB-8 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 76

background image

OPERATION

F-1097-2305

3-9

TABLE OF CONTENTS

Micro-Meter Box Calibration

for Unlisted Seeds

NOTE

Calibration Crank Assembly used for Calibration is stored
in the toolbox.

Brillion assumes no liability pertaining to Seeding Rates
achieved with this Seeder. Rates listed are general in
nature and should be used as starting points only. Seed
varieties and blends listed represent those calibrated
through in-house test meters.
Variations in actual rates may be realized due to
differences in seed lots. For accurate rates with seeds
being used, follow the calibration instructions listed on
the Seed Chart inside the Seed Box Cover or refer to this
Manual.

See Figure 3-19.

The information listed in the

Seed Chart is subject to change without notice.

Calibrate Unlisted Seeds as follows:

1. Seed Shaft turns 258 revolutions per acre seeded.
2. Raise machine and lock in Transport Position.
3. Place Calibration Tray in collection position to catch

seed. Remove the 5/16-18 Wing Nuts that secure the
Calibration Tray Cover over the opening in the RH
Support Plate.

See Figure 3-15.

Remove the 5/16-18

Wing Nut that secures the Calibration Tray in the
Storage position. Orient the Calibration Tray with
Handle to the top and insert it into the RH Support
opening.

See Figure 3-16.

4. Remove Micro-Meter Drive Pin.

See Figure 3-17.

5. Turn Transmission Micro-Meter Shaft Calibration Hex

258 revolutions Clockwise (CW) with provided Crank,
43 turns may be used if results are adjusted as stated
in Step 6.

6. Weigh seed for approximate planting rate in lbs/acre.

Multiply weight by 6, if only 43 turns were used.

Figure 3-15: Calibration Opening Cover

Figure 3-16: Calibration Tray Collection Position

Figure 3-17: Micro-Meter Box Calibration

7. Install Micro-Meter Drive Pin.
8. Place Calibration Tray back in storage position.

Figure 3-18.

Re-install Calibration Opening Cover

over the opening in the RH Support Plate with 5/16-18
Wing Nuts.

Figure 3-18: Calibration Tray Storage Position

Calibration

Opening Cover

Wing Nut,

5/16-18

RH Support

Plate Calibration

Tray Opening

RH Seed

Box Support

Calibration Tray

Calibration Tray

Storage Opening

RH Seed

Box Support

30 Tooth

15 Tooth

15 Tooth

218254

Calibration

Crank

Large Meter

Calibration Hex

Micro-Meter

Drive Pin

Idler

Calibration

Tray

Calibration

Opening Cover

Wing Nut,

5/16-18

RH Seed

Box Support

«
...
39
40
41
42
43
...
»

Содержание Brilllion Till'N Seed BPSB-8













































































Отзывы:

Нет отзывов

Похожие инструкции для Brilllion Till'N Seed BPSB-8

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: JB Systems Страницы: 12

Бренд: P.Lindberg Страницы: 76

Бренд: MacDon Страницы: 2

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: Velp Scientifica Страницы: 16

Бренд: Velp Scientifica Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды