Landoll 875-18 Скачать руководство пользователя страница 62

Страница: 62 / 64

PROBLEM

PROBABLE CAUSE:SOLUTION

5. PLUGGING BETWEEN DISC AND SPRAY

SHIELD

A. Dirt Not Flowing Under Shield:

Readjust spray

shield (usually up and/or to the rear).

Machine running too deep. Raise to proper

operating depth by adjusting stroke control depth

stop on master cylinder.

B. Conditions Too Wet:

Wait until conditions are

proper for tillage.

6. 10" SWEEPS WILL NOT PENETRATE

A. Machine Not Set Deep Enough:

Check for

correct pitch on sweeps (The correct pitch is 47

7. SHANKS NOT STRAIGHT UP AND DOWN ON

FRAME OR HAVE EXCESSIVE WEAR

A. Excessive Wear At Pivot Bolt:

Replace bolt-on

shank holder, if needed.

Replace bushing, if needed.

8. SHANK SPRINGS BREAKING

A. Spring Pivot Bolt Too Tight:

Spring pivot bolt

must be loose enough to allow spring plug to pivot

so spring is not forced to bend.

9. SCREW IN TOP OF SPRING BREAKING

A. Lock Nut Should Be Tightened Against Shank

Bracket Instead Of Spring Plug:

Verify that there

are three threads between lock nut and spring plug.

10. PLUGGING IN SHANK AREA

A. Shank Placement Not According To

Specifications:

Check shank placement against

Figures 2-1 through 2-7.

B. Ground Too Wet:

Wait until ground conditions

are proper for tillage.

11. REEL VIBRATING

A. Rear Of Machine Too Deep:

Level machine by

turning radius rod.

B. Running Machine Too Slow:

Machine needs to

be pulled at least 5.5 mph.

12. REEL COMING LOOSE IN FIELD

A. Reel Bearing Lock Collars Mounted On Wrong

Side Of Reel:

Mount lock collars on side of reel

toward center of machine.

Lock collars tightened in wrong direction. Lock in

direction of reel rotation.

5-2

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды