Landoll 875-18 Скачать руководство пользователя страница 51

Страница: 51 / 64

OPERATION AND MAINTENANCE

DANGER

NEVER ALLOW ANYONE TO RIDE ON

THE 875 SERIES TILLOLL AT ANY

TIME. ALLOWING A PERSON TO RIDE

ON THE MACHINE CAN INFLICT SERI-

OUS PERSONAL INJURY OR DEATH

TO THAT PERSON.

DANGER

DISC BLADES ARE EXTREMELY

SHARP. EXERCISE EXTREME CARE

WHEN WORKING ON OR NEAR DISC

BLADES. DO NOT ALLOW DISCS TO

ROLL OVER OR FALL ONTO ANY BOD-

ILY

PART.

NOT

ALLOW

WRENCHES TO SLIP WHEN WORKING

NEAR DISC BLADES. NEVER PUSH

WRENCHES TOWARD DISC BLADES.

DO NOT CLIMB OVER MACHINE

ABOVE DISC BLADES. FAILURE TO

STAY CLEAR OF DISC BLADE EDGES

CAN CAUSE SERIOUS PERSONAL IN-

JURY OR DEATH.

DANGER

STAND CLEAR OF WINGS WHILE

FOLDING OR UNFOLDING. ALL HY-

DRAULICALLY ELEVATED EQUIP-

MENT MUST HAVE CYLINDER LOCK-

OUTS INSTALLED OR BE LOWERED

TO THE GROUND, WHEN SERVICING

OR WHEN EQUIPMENT IS IDLE. FAIL-

URE TO TAKE PREVENTIVE MEAS-

URES AGAINST ACCIDENTAL LOWER-

ING CAN RESULT IN SERIOUS PER-

SONAL INJURY.

DANGER

ALWAYS LOCK THE TRACTOR DRAW-

BAR IN THE CENTER POSITION WHEN

TRANSPORTING THE UNIT. FAILURE

TO DO SO CAN RESULT IN SERIOUS

INJURY OR DEATH AND CAUSE DAM-

AGE TO THE EQUIPMENT.

DANGER

WHEN TRANSPORTING THE UNIT,

PLACE CYLINDER LOCKOUTS IN THE

TRANSPORT LOCK POSITION AFTER

FULLY EXTENDING THE CYLINDERS.

INSERT THE LOCKOUT PINS TO SE-

CURE THE CYLINDER LOCKOUTS.

FAILURE TO LOCKOUT THE CYLIN-

DERS CAN CAUSE THE UNIT TO SET-

TLE DURING TRANSPORT, WHICH

CAN RESULT IN SERIOUS INJURY OR

DEATH AND CAUSE DAMAGE TO THE

EQUIPMENT.

CAUTION

WHEN TRANSPORTING FARM IMPLE-

MENTS ON PUBLIC ROADS, IT IS THE

RESPONSIBILITY OF THE OPERATOR

TO ABIDE BY STATE AND LOCAL

LAWS CONCERNING WIDE LOADS,

SPEED, SAFETY EMBLEMS AND

SAFETY LIGHTING EQUIPMENT.

DRIVE AT SAFE SPEEDS. PARTICU-

LARLY WHEN ROUNDING CORNERS,

CROSSING ROUGH GROUND OR

DRIVING ON HILLSIDES, TO PREVENT

TIPPING THE TRACTOR.

4-1

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды