Landoll 875-18 Скачать руководство пользователя страница 53

Страница: 53 / 64

4-3 ATTACHING TO THE TRACTOR

4-3.1

Align the tractor drawbar with the ma-

chine. Raise or lower the Tilloll ring hitch, as

needed, using the swivel jack. Attach the unit

with proper size hitch pin.

4-3.2

Clean all hydraulic couplings and attach

to the tractor. When properly attached, the

hydraulic control lever should cause the

Tilloll to:

Lower to the ground when the control arm is

moved forward or downward, and

Raise when the control arm is moved back-

ward or upward.

4-3.3

Fully extend the hydraulic gauge wheel

cylinders, and place the cylinder lockouts in

the transport lock position over the cylinder

rods. Secure the lockouts with the lockout

pins

(See Figure 4-2).

4-3.4

Always place the swivel jack on the in-

terior mount before setting the machine in

motion.

4-3

Figure 4-2 Transport Locks

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды