Landoll 875-18 Скачать руководство пользователя страница 59

Страница: 59 / 64

4-11 WHEEL BEARING MAINTENANCE

Wheel bearing maintenance should be per-

formed at the beginning of every season of use.

Check the wheel bearings periodically for exces-

sive end play. If needed, adjust or replace them

using the following procedure:

4-11.1

Place the frame on blocks or stands

sufficient to lift the tire clear of the ground.

4-11.2

Remove the hub cap, cotter pin, slotted

nut and washer.

4-11.3

Remove the hub. Clean and inspect the

bearings and hub cavity. Replace any worn

or defective parts.

4-11.4

Repack the bearings using a high-

quality wheel bearing grease.

4-11.5

Reinstall the hub with a new seal and

the inner bearing in place.

4-11.6

Install the outer bearing cone, washer

and slotted nut.

4-11.7

Tighten the slotted nut while rotating the

hub until there is a slight resistance to wheel

rotation. Then, back the slotted nut off one

notch, until the wheel rotates freely without

end play.

4-11.8

Install a new cotter pin and replace the

hub cap.

4-12 HYDRAULIC MAINTENANCE

4-12.1

Check the tractor hydraulic fluid level

per tractor owners manual and after any

leakage. Check fluid level with the cylinders

in the retracted position.

4-12.2

If a cylinder or valve leaks, disassemble

the parts to determine the cause of the leak.

Any time a cylinder is opened up, or when-

ever any seal replacement is necessary, it is

advisable to clean all parts and replace all

seals. Seal kits are available from your Lan-

doll dealer.

4-12.3

Check all hydraulic hoses weekly. Look

for binding or cracking. Replace all worn or

defective parts immediately.

4-13 LUBRICATION

4-13.1

Table 4-1 and Figure 4-6

specifies the

number and the period of lubrication points

on the

875 Series Tilloll

. Proper mainte-

nance of your machine will, under normal op-

erating conditions, help to keep it operating

at or near its peak performance for an ex-

tended period of time. Proper maintenance is

also a condition of keeping your warranty in

good status.

4-14 STORAGE

4-14.1

The service life of the Tilloll will be ex-

tended by proper off-season storage prac-

tices. Prior to storing the unit, complete the

following procedures:

Completely clean the unit.

Inspect the machine for worn or defective

parts. Replace as needed.

Repaint all areas where the original paint

film is worn off.

Grease all exposed metal surfaces of

shanks, points and discs.

Lubricate each point of the machine as

stated in

Section 4-13.

4-14.2

Store the unit in a shed or under a tar-

paulin to protect it from the weather. The

ground tools and tires should rest on boards,

or some other object, to keep them out of

the soil.

4-9

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды