Landoll 875-18 Скачать руководство пользователя страница 63

Страница: 63 / 64

PROBLEM

PROBABLE CAUSE:SOLUTION

13. REEL NOT MOVING SOIL ADEQUATELY

A. Reel Mounted Backwards:

Mount again per

assembly instructions.

B. Running Machine Too Slow:

Machine needs to

be pulled at least 5.5 mph.

C. Machine Not Level:

Adjust radius rod to level

machine.

14. ROCKS JAMMING IN END OF REEL AND

LOCKING UP REEL

A. Reel Blade Too Long:

Cut 1-1/2" off the end of

reel blade.

B. Reel Angle Wrong For Terrain:

Cut blade off at

angle toward rear of blade to provide a relief area for

rocks.

15. HARROW PLUGGING

A. Improperly Set Harrow:

Set according to

operating instructions.

16. WINGS FOLDING TOO FAST

A. Restrictor Elbows Not Installed

: Check to make

sure restrictors are installed per assembly

instructions.

Idle tractor when folding.

Turn tractor hydraulic flow down.

Engage hydraulic valve. Hold fully engaged until

folded.

17. MACHINE RUNNING DEEP TO ONE SIDE

A. Distance From Frame To Axle Of Gauge

Wheels Differ:

1) Set all depth stops the same. 2)

Raise machine until all cylinders are fully extended.

3) Measure cylinders from pin to pin. Verify that all

cylinders are same length. 4) If measurements are

not the same,

see Sections 3-6 or 3-7

to readjust

cylinder length.

Wing cylinders may need to vary in length from main

cylinders, per soil conditions.

Check that tires are same size and pressure is

correct.

Check for hydraulic leakage and repair.

18. CYLINDERS BROKEN IN TRANSPORT

A. Machine Not Properly Secured During

Transport:

Use transport locks and let machine

down on locks during transport.

5-3

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды