Landoll 875-18 Скачать руководство пользователя страница 29

Страница: 29 / 64

3-5 GAUGE WHEEL INSTALLATION

3-5.1

All gauge wheel arms, rockshafts, and

hubs come already assembled from the fac-

tory.

3-5.2

Mount the tires on the wheels and in-

stall on the hubs.

Recommended tires: 11L X 15 10 ply

3-6 HYDRAULIC LIFT INSTALLATION - RIGID AND 15’ FOLD

IMPORTANT

READ ALL SAFETY PRECAUTIONS AT THE

FRONT OF THE SECTION BEFORE ATTEMPT-

ING ANY OF THE FOLLOWING PROCEDURES.

3-6.1

Install stroke control and stroke control

cover on master cylinder(s), and parallel sys-

tem cylinder on 15’ fold model. Replace cyl-

inder yoke(s). Adjust cylinder extended

length to measure 28-1/4" from hole center

to hole center. Tighten lock bolt or set screw

to lock yoke in place. NOTE: Always adjust

the slave cylinder extended length to meas-

ure the same as the master cylinder to allow

the unit to operate level in the field.

3-6.2

Install the master cylinders (all models)

and slave cylinder (rigid models) on the main

frame ports up, using clevis pin and cotter

pins. Connect rod to gauge wheel arm or

rockshaft using extended pin and 1/4 hair

pins.

3-6.3

Install the slave cylinder(s) (all fold mod-

els) on the wing frame ports up, using clevis

pin and cotter pins. Connect rod to gauge

wheel arm or rockshaft using extended pin

and 1/4 hair pins.

3-6.4

Install 90

elbows with restrictors into

base and rod end of each lift cylinder.

3-6.5

Install hoses per

Figures 3-6 and 3-7

and

Table 3-1.

IMPORTANT

ALL CYLINDER PORTS ARE PLUGGED. DO

NOT FORGET TO REMOVE ALL PLUGS AND

REPLACE WITH HOSES OR FITTINGS BEFORE

APPLYING HYDRAULIC PRESSURE TO CYLIN-

DERS.

3-9

ITEM

PART NO.

HOSE LENGTH (MODEL USED)

3-397-010038

114" (10’-6")

1-397-010311192

192" (13’-6" & 15’)

3-397-010202

236" (10’-6")

1-397-010311286

286" (13’-6" & 15’)

3-397-010125

251" (15F)

1-397-010112

41" (15F)

1-397-010083

28" (15F)

1-397-010115

114" (15F)

1-397-010111

152" (15F)

Table 3-1 Hydraulic Hose Installation -

Rigid and 15’ Fold

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды