Landoll 875-18 Скачать руководство пользователя страница 43

Страница: 43 / 64

3-12 PULL HITCH INSTALLATION - 15’F MODEL

3-12.1

Install pull hitch assembly to frame us-

ing hitch pins and 1/4 x 2-1/2 cotter pins

(See Figure 3-14).

3-12.2

Attach radius rod assembly to mast us-

ing extended cylinder pin and 1/4 x 2 cotter

pins.

IMPORTANT

THE RADIUS ROD AFFECTS TWO ADJUST-

MENTS:

IT LOCATES THE PULL HITCH CLEVIS AT THE

PROPER HEIGHT FOR THE TRACTOR DRAW

BAR.

IT LEVELS THE MACHINE. LENGTHENING AND

SHORTENING CAN BE ACCOMPLISHED BY

USING THE RADIUS ROD HANDLE.

3-12.3

Install jack on pull hitch using hitch pin

w/ chain included.

IMPORTANT

REMOVE THE 1/4 HAIR PIN AND TRAIL PIN BE-

FORE FOLDING AND UNFOLDING. PINS MUST

BE IN PLACE WHILE OPERATING OR TRANS-

PORTING EQUIPMENT.

3-13 PULL HITCH INSTALLATION - ALL OTHER MODELS

3-13.1

Install pull hitch assembly to frame us-

ing hitch pins, flat washers, and 1/4 x 2-1/2

cotter pins

(See Figure 3-15).

3-13.2

Install hitch ring assembly to pull hitch

assembly using 1-8 x 8 or 1-8 x 8-1/2 hex

head cap screw, flat washer, hitch bushing,

and hex lock nut.

3-13.3

Install radius rod assembly attached to

pull hitch to mast using extended cylinder pin

and 1/4 x 2 cotter pins.

IMPORTANT

THE RADIUS ROD AFFECTS TWO ADJUST-

MENTS:

IT LOCATES THE PULL HITCH CLEVIS AT THE

PROPER HEIGHT FOR THE TRACTOR DRAW

BAR.

IT LEVELS THE MACHINE. LENGTHENING AND

SHORTENING CAN BE ACCOMPLISHED BY

USING THE RADIUS ROD HANDLE.

3-13.4

For all fold models, install hose bracket

on pull hitch with special nut and 1/2-13 hex

nut. On all rigid models, install hose bracket

and hose bracket mount to pull hitch assem-

bly using 1/2-13 x 1-1/2 hex head cap screw,

hex lock nut, special nut, and hex nut

(See

Figure 3-15)

3-13.5

Install jack to pull hitch assembly using

hitch pin with chain included.

3-23

Содержание 875-18

































































Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды

Landoll 875-18, Руководство оператора

Результаты поиска

Содержание 875-18

Отзывы:

Похожие инструкции для 875-18

Бренды по названию

Популярные бренды