Landoll 1230 Series Скачать руководство пользователя страница 45

Страница: 45 / 64

4-5.2

Transport Safety Chain

Attach transport safety chain to chisel plow

hitch with 1" x 8

" bolt furnished with machine

bundle. Tighten bolt securely

(See Figure

4-10)

Attach chain clevis to tractor drawbar with

bolt and locknut furnished in chain bundle.

Thread chain through clevis, then attach

chain around tractor drawbar frame. Adjust

chain slack to allow chisel plow to turn

(See

Figure 4-11)

Connect chain hook and secure with latch.

WARNING

ALWAYS USE TRANSPORT SAFETY

CHAIN WHEN TRANSPORTING IMPLE-

MENT. FAILURE TO DO SO COULD

CAUSE SERIOUS PERSONAL INJURY

AND MACHINE DAMAGE IF IMPLE-

MENT BECOMES UNHOOKED FROM

TOWING VEHICLE.

4-6 PURGING THE HYDRAULIC SYSTEM

Purge the air from the hydraulic system before

going to the field:

Hold tractor hydraulic control lever in “open”

position a few seconds after implement is fully

raised.

Lower implement and hold lever in “closed”

position a few seconds after implement is fully

lowered.

WARNING

RECHECK FLUID LEVEL IN TRACTOR

RESERVOIR AFTER PRIMING HY-

DRAULIC SYSTEM. FAILURE TO DO

SO CAN RESULT IN PERSONAL IN-

JURY AND / OR DAMAGE TO TRAC-

TOR OR IMPLEMENT. ADD FLUID AS

REQUIRED.

4-9

Figure 4-10 Transport Safety Chain

Figure 4-11 Transport Safety Chain Attached

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды