Landoll 1230 Series Скачать руководство пользователя страница 14

Страница: 14 / 64

WARNING

1. USE LIFT CRANE, JACK, TACKLE

OR FORK LIFT TRUCK TO LIFT HEAVY

PARTS AND ASSEMBLIES.

2. KEEP CLEAR OF PARTS WHICH

MAY MOVE OR DROP WHEN REMOV-

ING SHIPPING STRAPS OR BRACK-

ETS.

3. IF MACHINE REQUIRES BLOCKING

UP, USE BLOCKING MATERIAL OF

ADEQUATE STRENGTH AND IN GOOD

CONDITION. BLOCKS MUST BE ON A

SMOOTH DRY SURFACE.

4. NEVER PLACE ANY PART OF YOUR

BODY UNDER BLOCKED-UP ASSEM-

BLIES.

5. IF WELDING OR FLAME-CUTTING IS

REQUIRED, BE SURE NO FLAMMABLE

MATERIALS ARE IN THE AREA. ALSO,

CLEAR BYSTANDERS FROM AREA.

WARNING

1. WEAR PERSONAL PROTECTIVE

EQUIPMENT (PPE) SUCH AS, BUT NOT

LIMITED TO, PROTECTION FOR EYES,

LUNGS, EARS, HEAD, HANDS AND

FEET WHEN OPERATING, SERVICING

OR REPAIRING EQUIPMENT.

2. NEVER USE YOUR HANDS TO LO-

CATE A HYDRAULIC LEAK. USE A

PIECE OF WOOD OR CARDBOARD.

HYDRAULIC FLUID ESCAPING UNDER

PRESSURE CAN PENETRATE THE

SKIN CAUSING SERIOUS INJURY.

3. OPENINGS IN THE SKIN AND MINOR

CUTS ARE SUSCEPTIBLE TO INFEC-

TION FROM HYDRAULIC FLUID. IF IN-

JURED BY ESCAPING FLUID, SEE A

DOCTOR AT ONCE. WITHOUT IMMEDI-

ATE MEDICAL TREATMENT, SERIOUS

INFECTION CAN OCCUR.

3-2

Figure 3-1 Hydraulic Leak Detection

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды