Landoll 1230 Series Скачать руководство пользователя страница 44

Страница: 44 / 64

4-5 ATTACHING TO TRACTOR

4-5.1

Hitch

The implement is equipped with a combination

clevis / tongue swivel hitch. For a tongue-type trac-

tor drawbar, use the clevis hitch end. If the tractor

has a clevis-type drawbar, use the tongue hitch

end

(See Figure 4-8)

WARNING

TO AVOID SERIOUS INJURY OR

DEATH, STOP TRACTOR ENGINE,

SHIFT TO PARK POSITION OR SHIFT

TO NEUTRAL AND SET BRAKES BE-

FORE LEAVING TRACTOR.

Note: Relieve internal hydraulic system pres-

sure before leaving tractor seat.

Hitch tractor to implement with a 1" (25 mm)

(minimum diameter).

Secure pin in place

with a clip pin.

Remove jack and pin in storage position on

top of hitch tube

(See Figure 4-9)

Connect hydraulic hoses for frame and disc

cutter circuits to tractor couplers. Connect so

when tractor lever is pulled rearward, imple-

ment raises.

IMPORTANT

THOROUGHLY CLEAN HOSE COUPLERS AND

TRACTOR COUPLINGS BEFORE CONNECTING

HOSES.

4-8

Figure 4-8 Combination Swivel Hitch

Figure 4-9 Implement Hitch

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды