Landoll 1230 Series Скачать руководство пользователя страница 38

Страница: 38 / 64

WARNING

1. DO NOT CLEAN, ADJUST OR SERV-

ICE WHEN THE MACHINE IS IN MO-

TION.

2. ALL HYDRAULICALLY OR ME-

CHANICALLY ELEVATED COMPO-

NENTS MUST BE BLOCKED TO PRE-

VENT ACCIDENTAL LOWERING OR

MUST BE LOWERED TO THE GROUND

WHEN ADJUSTMENTS OR REPAIRS

ARE MADE.

3. PROPERLY TIGHTEN ALL MOUNT-

ING HARDWARE. SEE BOLT TORQUE

CHART.

4. PERIODICALLY INSPECT ALL MOV-

ING PARTS FOR WEAR AND REPLACE

WITH ONLY AUTHORIZED SERVICE

PARTS IF ANY EXCESSIVE WEAR IS

PRESENT. IF SAFETY DECALS ARE

MISSING, ILLEGIBLE, OR DAMAGED,

THEY SHOULD BE REPLACED.

CAUTION

1. WEAR PERSONAL PROTECTIVE

EQUIPMENT (PPE) SUCH AS, BUT NOT

LIMITED TO, PROTECTION FOR EYES,

LUNGS, EARS, HEAD, HANDS AND

FEET WHEN OPERATING, SERVICING

OR REPAIRING EQUIPMENT. DO NOT

WEAR LOOSE CLOTHING OR JEW-

ELRY AS IT MAY ENTANGLE OR

CATCH ON MOVING PARTS.

2. NEVER USE YOUR HANDS TO LO-

CATE A HYDRAULIC LEAK. USE A

PIECE OF WOOD OR CARDBOARD.

HYDRAULIC FLUID ESCAPING UNDER

PRESSURE CAN PENETRATE THE

SKIN CAUSING SERIOUS INJURY.

3. OPENINGS IN THE SKIN AND MINOR

CUTS ARE SUSCEPTIBLE TO INFEC-

TION FROM HYDRAULIC FLUID. IF IN-

JURED BY ESCAPING FLUID, SEE A

DOCTOR AT ONCE. WITHOUT IMMEDI-

ATE MEDICAL TREATMENT, SERIOUS

INFECTION CAN OCCUR.

4-2

Figure 4-1 Hydraulic Leak Detection

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды