Landoll 1230 Series Скачать руководство пользователя страница 58

Страница: 58 / 64

4-25 DEPTH CONTROL SYSTEM

4-25.1

The DCS 3000 Depth Control System al-

lows automatic or manual depth control of

towed implements

(See Figure 4-37)

. An op-

erator’s and installation instruction manual is

included with the system bundle.

4-26 POINTS FOR SHANKS

4-26.1

Two types of points are available for the

standard shanks

(See Figure 4-38)

Straight points for minimum residue distur-

bance

Twisted points for incorporating some resi-

due

Note: Install an equal number of right and left

twisted points. See Basic Setup Assembly In-

structions, #2PD654399 for point location.

4-26.2

Two points and shank wear strip combina-

tions are available

(See Figure 4-39)

Flow points and beveled wear strips for

minimum residue disturbance.

Flat points with flat wear strips for incorpo-

rating some residue.

4-22

Figure 4-37 Depth Control System Console

Figure 4-38 Points for Standard Shanks

Figure 4-39 Points for Deep-Till Shanks

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды