Landoll 1230 Series Скачать руководство пользователя страница 39

Страница: 39 / 64

CAUTION

1. COMPLY WITH YOUR STATE AND

LOCAL LAWS GOVERNING HIGHWAY

SAFETY, LIGHTING & MARKING, AND

THE MOVEMENT OF FARM MACHIN-

ERY ON PUBLIC ROADS.

2. ALWAYS DRIVE AT A REASONABLE

SPEED TO MAINTAIN CONTROL OF

THE EQUIPMENT. DO NOT TOW AT

SPEEDS IN EXCESS OF 20 MPH.

3. USE A SMV (SLOW MOVING VEHI-

CLE) EMBLEM AT ALL TIMES.

4. USE APPROVED EXTREMITY LIGHT-

ING AND WARNING DEVICES TO

WARN OPERATORS OF OTHER VEHI-

CLES ON THE HIGHWAY DURING

TRANSPORT.

5. NEVER TRANSPORT MACHINE UN-

LESS HYDRAULIC SYSTEMS ARE

COMPLETELY CHARGED WITH HY-

DRAULIC OIL AND THE TRANSPORT

SAFETY LOCKS ARE ENGAGED.

6. PLAN YOUR ROUTE TO AVOID

HEAVY TRAFFIC.

7. BE A SAFE AND COURTEOUS OP-

ERATOR.

8. THE MINIMUM WEIGHT OF THE

TOWING VEHICLE SHOULD BE AT

LEAST EQUAL IN WEIGHT OF THE

TOWED IMPLEMENT.

CAUTION

1. UTILIZE TRANSPORT CHAINS. THE

TRANSPORT CHAIN SHOULD BE AD-

JUSTED SO THAT THE TONGUE OF

THE TOWED MACHINE WILL NOT

TOUCH THE GROUND IN CASE OF

LOSS OR BREAKAGE OF THE HITCH

ASSEMBLY OR PIN.

2. AVOID SHARP TURNS USING

BRAKES. DRIVE SLOWLY OVER

ROUGH GROUND, SIDE HILLS AND

AROUND CURVES TO AVOID TIPPING.

CAUTION

1. ALWAYS SHUT OFF TRACTOR,

SHIFT TO “PARK” POSITION (OR

SHIFT TO NEUTRAL), SET BRAKES

AND CYCLE HYDRAULIC LEVERS BE-

FORE DISMOUNTING TRACTOR OR

WORKING AROUND THE MACHINE.

2. REMOVE TRACTOR START KEY

WHEN TRACTOR AND IMPLEMENT

WILL BE UNATTENDED.

3. NEVER LEAVE UNATTENDED

EQUIPMENT IN THE UNLOCKED

RAISED POSITION. LOWER THE UNIT

TO THE GROUND OR USE TRANS-

PORT LOCKS.

4. DO NOT LEAVE TRACTOR OR IM-

PLEMENT UNATTENDED WITH TRAC-

TOR ENGINE RUNNING.

DANGER

NEVER ALLOW ANYONE TO RIDE ON

THIS EQUIPMENT.

4-3

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды