Landoll 1230 Series Скачать руководство пользователя страница 46

Страница: 46 / 64

4-7 UNHITCHING FROM TRACTOR

WARNING

TO AVOID SERIOUS INJURY OR

DEATH, STOP TRACTOR ENGINE,

SHIFT TO PARK POSITION OR SHIFT

TO NEUTRAL AND SET BRAKES BE-

FORE UNHITCHING.

4-7.1

Chisel Lowered

IMPORTANT

TO PREVENT CHISEL POINT DAMAGE, DO

NOT LOWER CHISEL ON CONCRETE OR

ROCKS.

Choose a level area to unhitch. Lower chisel

plow to ground.

Using tractor control lever, relieve pressure

in hydraulic system.

Disconnect hydraulic hoses and install cou-

pler dust caps.

Install jack. Remove transport safety chain

and hitch pin.

Perform “End of Day” service as outlined in

the SERVICE Section.

4-7.2

Chisel Raised

Choose a level area to unhitch.

Install lockup on rockshaft and secure with

L-pin and cotter pin

(See Figure 4-12)

Securely block wheels.

Section 4-7.1., steps b. - e.

4-10

Figure 4-12 Lockup in Lockup Position

Содержание 1230 Series

































































Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды

Landoll 1230 Series, Руководство оператора

Результаты поиска

Содержание 1230 Series

Отзывы:

Похожие инструкции для 1230 Series

Бренды по названию

Популярные бренды