Land Pride RCG3715, Руководство оператора

Страница: 17 / 66

Section 1: Assembly & Set-up
RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M 1/26/21
13
Table of Contents
Section 1: Assembly & Set-up
Tractor Requirements
Horsepower
Tractor horsepower should be within the range noted
below. Tractors outside the range must not be used.
Horsepower rating . . . . . . . . . . . . . . . . . . . . . . 50-160
Hitch type (See Drawbar Set-up) . . . . . . . . . Drawbar
Rear power take-off speed:
RC(M)3715 . . . . . . . . . . . . . . . . . . . . . . . . 540 rpm
RCG(M)3715 . . . . . . . . . . . . . . . . . . . . . . 1000 rpm
Hydraulic outlets (See Hydraulic Set-up)
Factory standard . . . . . . . . . . . . . . 2 Duplex outlets
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . 7-pin outlet
Drawbar Set-up
Refer to Figure 1-1:
DANGER
!
To avoid serious injury or death:
•
Do not use a power take-off adapter. The adapter will
increase strain on the tractor’s power take-off shaft causing
possible damage to shaft and driveline. It will also defeat
the purpose of the tractor’s power take-off shield.
•
Lightweight tractors with rear attached implements may
need weights added to the front to maintain steering control.
Consult your tractor Operator’s Manual to determine
proper weight requirements and maximum weight
limitations.
WARNING
!
To avoid serious injury or death:
•
Do not use a tractor that is too small or too large. Small
tractors can be pushed around and flipped over. Large
tractors can damage the attached implement.
•
Power take-off and/or driveline damage may occur if
distances “A” and “B” are not properly maintained.
Maintain proper distance, dimension “A”, between center
of drawbar hitch pin hole and end of tractor power take-off
shaft.
For 540 rpm & small 1000 rpm power take-off shafts:
“A” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14"- 16"
“B” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8" - 10"
“C”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18" - 22"
Power Take-Off Shaft to Drawbar Distance
Figure 1-1
22273a
Power Take-Off Shaft
Ground Level
B
C
Drawbar
A
Hydraulic Outlets
Two or three duplex outlets are required depending on
the fold option. Two outlets are needed when choosing a
fold option where the wings float simultaneously. Three
outlets are needed when choosing a fold option where
the wings fold independently.
It is highly recommended to connect the wing fold
hose(s) to a duplex outlet with fold capabilities and use
the float when in field operation.
Accessory available to convert from 2 duplexes to 1
duplex.
Before You Start
Read and understand this Operator’s Manual for your
cutter. An understanding of how the cutter works will aid
in the assembly and setup of your cutter.
It is best to go through the
Assembly Checklist before
assembling the cutter. Speed up your assembly task and
make the job safer by having all needed parts and
equipment readily at hand.
Torque Requirements
See “Torque Values Chart for Common Bolt Sizes” on
page 60 to determine correct torque values when
tightening hardware. See “Additional Torque Values” at
bottom of chart for exceptions to common torque values.
Assembly Checklist
Check Ref.
Have a fork lift or loader with properly sized chains and safety
stands capable of lifting and supporting the equipment on hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose parts
are shipped with the machine.
Operator’s
Manual
Double check to make sure all parts, fasteners,
and pins are installed in the correct location. Refer
to the Parts Manual if unsure. By double checking,
you will lessen the chance of using a bolt
incorrectly that may be needed later.
NOTE:
All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if removed
during assembly. Keep parts separated.
Operator’s
Manual
330-502M
Parts
Manual
331-939P
Make sure working parts move freely, bolts are
tight & cotter pins are spread.
Page 60
Make sure all grease fittings are in place and
lubricated.
Page 49
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Page 6
Make sure all red and amber reflectors are
correctly located and visible when machine is in
transport position.
Page 11
Make sure all pneumatic tires are properly inflated
and all wheel bolts and axle nuts are tightened to
the specified torque.
Page 60