manualshive.com logo in svg

Land Pride RCG3715, Руководство оператора, Страница: 48 / 66

Поделиться
Скачать
Land Pride RCG3715 Скачать руководство пользователя страница 48

Section 5: Maintenance & Lubrication

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

44

Table of Contents

Wing Gearbox Driveline Shield Access

Figure 5-5

Drivelines

Before each use, check that all driveline shields and 

drivelines are in place, undamaged and in working order. 

Replace shields and drivelines as needed. Order only 

genuine Land Pride parts from your local Land Pride 

dealer

DANGER

!

To avoid serious injury or death:  
Tractor power take-off shaft shield, driveline shields, and 

gearbox shaft shields must be installed and in good working 

condition to avoid driveline entanglement and projectiles 

flying off of the driveline.

WARNING

!

To avoid serious injury or death:  
Do not operate a broken or bent driveline. Such a driveline 

will break apart while rotating at high speeds and can cause 

serious injury or death. Always remove the implement from 

use until the damaged driveline can be repaired or replaced.

Drivelines With Slip Clutches

WARNING

!

To avoid serious injury or death:  

•

Always follow “Tractor Shutdown Procedure” provided in 

this manual before dismounting the tractor.

•

A slip clutch that has been in use or has slipped for as little 

as only two or three seconds during run-in may be too hot 

to touch. Allow a hot clutch to cool before working on it.

Friction clutches must be capable of slippage during 

operation to protect gearboxes, drivelines, and other 

drive train parts. Friction clutches should be “run-in” prior 

to initial operation and after periods of inactivity to 

remove any oxidation from the friction surfaces. Repeat 

“run-in” at the beginning of each season and when 

moisture seizes the inner friction plates.

IMPORTANT: 

Prior to initial operation and after 30 

days of inactivity, slip friction disks to remove 

oxidation and moisture. Moisture allows disks to slip 

easily. Oxidation can prevent disk from slipping 

causing driveline damage. This damage is NOT 

covered under the warranty.

Wing Gearbox Driveline Shield Access

Refer to Figure 5-5:

1. To remove shaft guard (#1) at the spindle gearbox, 

use a flat head screw driver to unsnap latches (#2) on 

both sides of guard (#1) and slide shaft guard over 

driveline to expose driveline yoke. Do not unhook 

safety chain (#3).

2. When servicing of driveline yoke is completed, return 

shaft guard to its original position and secure with 

latches (#2).

3. Check safety chain (#3). Make sure it is latched to 

shaft guard mounting plate (#4) and shaft guard (#1).

Center Gearbox Driveline Shield Access

Refer to Figure 5-4:

1. To access the center driveline, push the latch release 

button to open latch (#1).

2. Pull up on the splitter box shield (#2) and let it rest on 

the center driveline shield (#3).

3. Pull up on the center driveline shield (#3) until it rests 

in vertical position.

4. When servicing of driveline is completed, return 

shielding to its original position.

5. Press down on the latch lever to engage latch (#1). 

Latch should clamp shield tightly to the shield 

bracket (#4). If not, adjust the length of the bolt on the 

latch to change the clamping pressure and secure 

the bolt position with the jam nut.

Center Gearbox Driveline Shield Access

Figure 5-4

70555

70547

Содержание RCG3715



































































Отзывы:

Нет отзывов