Land Pride RCG3715 Скачать руководство пользователя страница 29

Страница: 29 / 66

Section 1: Assembly & Set-up

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

Purge Hydraulic System

DANGER

To avoid serious injury or death:
Never remove or install a folding wing cylinder with cylinder

rod retracted and wing folded-up. The wing is unstable

without its folding cylinder and can suddenly fall. Also, air

trapped in a new or repaired cylinder will drop the wing

suddenly when lowering the wing. Either situation can render

the cutter inoperable and cause serious bodily injury or death.

WARNING

To avoid serious injury or death:
Be sure center and wing decks are lowered to the ground and

all hydraulic pressure is relieved before disconnecting any

hydraulic lines or fittings to purge the hydraulic system.

Wing Fold Cylinder

Refer to Figure 1-26:

1. Lower center deck until it is supported by stroke

control flip spacers (#6) on hydraulic cylinder (#4).

2. Lower wing decks until they rest on the ground.
3. See

“Tractor Shutdown Procedure”

on page 15.

Shut tractor down properly and move deck lift control

lever back and forth to relieve all hydraulic pressure.

4. Slightly loosen hydraulic hose fitting (#2) on right-

hand wing cylinder (#1) to allow air to escape.

5. Restart tractor and slowly activate tractor control

lever to retract wing cylinder (#1), and to purge

trapped air from the hydraulic system.

6. Shut tractor down properly. See

“Tractor Shutdown

Procedure”

on page 15.

7. Tighten hose fitting (#2) at right-hand wing cylinder.
8. Repeat steps 4-7 to purge the left-hand wing cylinder

(#3).

Deck Lift Cylinder

Refer to Figure 1-26:

1. Move all hydraulic stroke control flip spacers (#6) to

open position, then proceed to lower center deck.

2. See

“Tractor Shutdown Procedure”

on page 15.

Shut tractor down properly and move deck lift control

lever back and forth to relieve all hydraulic pressure.

3. Slightly loosen hydraulic hose fitting (#5) on deck lift

cylinder (#4) to allow air to escape.

4. Restart tractor and slowly activate tractor control lift

lever to extend lift cylinder (#4) and to purge trapped

air from the hydraulic system.

5. Shut tractor down properly. See

“Tractor Shutdown

Procedure”

on page 15.

6. Tighten hose fitting (#5) on lift cylinder (#4).

Purge Wing & Center Deck Cylinders

Figure 1-26

70510

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды