background image

Section 1: Assembly & Set-up

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

20

Table of Contents

Wing Axle - Turnbuckle

Figure 1-15

Wing Axle Turnbuckle Set-up

Refer to Figure 1-15:

1. Park tractor and cutter on a level surface.
2. Shut tractor down properly before dismounting. Refer 

to 

“Tractor Shutdown Procedure” 

on page 15.

3. Loosen jam nut (#2) on turnbuckle (#1) and adjust 

until center of ball swivels are approximately 10 1/2" 

apart. Do not tighten jam nut. Final adjustment will be 

made later when leveling wing decks.

4. Repeat step 3 for the left wing axle.

Unfold Wings

DANGER

!

To avoid serious injury or death:  

Keep everyone out of the area where the wing decks will 

unfold. One of the wing decks can fall suddenly.

Do not walk, stand, or allow anyone else in the area where 

a raised wing will fall unless the wing is securely locked in 

the raised position with its transport lock..

Refer to Figure 1-16: 

1. Park tractor and cutter on a level surface.
2. Release any tension on transport lock pins (#2) by 

raising both wings up slightly. 

3. Without relieving hydraulic pressure, shut tractor 

down properly before dismounting. Refer to 

“Tractor 

Shutdown Procedure” 

on page 15.

70499

NOTE:  

The cutter is shipped with turnbuckles 

attached and drawn all the way in as shown in 

Figure 1-15

.

4. Remove hairpin cotter (#1) from both the left and right 

transport pins (#2).

5. Pull transport pins (#2) from lock holes (#3) on both 

wings as shown.

Refer to Figure 1-17: 

6. Store transport pins (#2) in storage holes (#3) as 

shown and secure with hairpin cotters (#1).

7. Return to the tractor, staying clear of unpinned wings.

a. For cutters equipped with single-action fold 

cylinders, restart tractor and place tractor control 

lever for wing cylinders to float position. Return to 

the cutter, staying clear of unpinned wings and 

carefully position yourself on the center deck. 

Manually push on the right wing until it starts to fall 

on its own. The wing should fall slowly as the 

hydraulic line is orificed to control the fall. If it does 

not fall on its own, then continue lowering the wing 

with tractor hydraulics. Repeat for left wing.

b. For cutters equipped with dual-action fold 

cylinders, restart tractor and lower both left and 

right wings with tractor hydraulic control lever until 

both wings are on the ground.

Transport Pin

Figure 1-16

Transport Pin, Storage Position

Figure 1-17

70507

70508

Содержание RCG3715



































































Отзывы: