Land Pride RCG3715 Скачать руководство пользователя

Страница: 47 / 66

Section 5: Maintenance & Lubrication

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

Chain Guards

Before each use of the cutter, check that all chain guards

are present, undamaged and in working order. Replace

any damaged or missing chain guard components as

needed. Order only genuine Land Pride parts from your

local Land Pride dealer.

DANGER

To avoid serious injury or death: Rotary Cutters have the

ability to discharge objects at high speeds; therefore, the use

of front & rear safety guards is mandatory with this cutter.

Double row chain guards should be used when cutting along

roadways and in areas where people may be present. Stop

blade rotation if bystanders are in or around the area. It is

operator and cutter on an open air tractor.

Skid Shoes

WARNING

To avoid serious injury or death: Excessive wear on skid

shoes may cause inadequate operation of cutter and create a

safety hazard.

Two skid shoes are mounted on the center section and

one skid shoe mounted on each wing section. Check all

skid shoes for wear and replace if necessary. Order only

genuine Land Pride parts from your local Land Pride

dealer.

Wing Skid Shoes

Refer to Figure 5-2:

Replace wing skid shoes as follows:
1. Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2),

and left-hand skid shoe (#1) as shown.

2. Plow bolts (#2) should be checked for wear and

replaced if necessary.

3. Attach new left-hand skid shoe (#1) to cutter with

3/8" plow bolts (#2) and secure with 3/8" hex whiz

nuts (#3). Tighten bolts to the correct torque.

4. Repeat for the right-hand wing.

Center Skid Shoes

Refer to Figure 5-3:

Replace center skid shoes as follows:
1. Remove 5/8"-11 hex flange nuts (#4), 5/8" -11 x 4"

GR5 bolts (#3), and right-hand center skid

shoe (#1) from the center deck frame (#2) as shown.

2. Attach new skid shoe (#1) to cutter with existing

5/8" bolts (#3), and secure with existing 5/8" hex

flange nuts (#4). Tighten bolts to the correct torque.

3. Repeat steps 1 & 2 for left-hand center skid shoe.

IMPORTANT:

Excessive wear on skid shoes can

weaken cutter side panels and cause damage that

will require extensive repairs. Always replace skid

shoes at the first sign of wearing thin.

Wing Skid Shoes

Figure 5-2

Center Skid Shoes

Figure 5-3

Gearbox Driveline Shielding

Check that the wing gearbox driveline shielding and

center gearbox driveline shielding is undamaged and in

working order. Replace any damaged components as

needed. Order only genuine Land Pride parts from your

local Land Pride dealer

DANGER

To avoid serious injury or death:
Tractor power take-off shaft shield, driveline shields, and

gearbox shaft shields must be installed and in good working

condition to avoid driveline entanglement and projectiles

flying off of the driveline.

# Part No.

Description

1 331-792H BEVELED SKID SHOE RH
1 331-793H BEVELED SKID SHOE LH
2 802-466C PLOW BOLT, 3/8" - 16 x 1 1/4" GR5

70475

# Part No.

Description

1 331-688H CENTER SKID SHOE (RIGHT & LEFT)

70476

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды