Land Pride RCG3715 Скачать руководство пользователя

Страница: 22 / 66

Section 1: Assembly & Set-up

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

Bar-Tite Hitch Hook-up

Attach Bar-Tite Hitch to Tractor Drawbar

Refer to Figure 1-12:

1. Insert 1" x 5 1/2" hex bolt (#1) through hitch top

plate (#2), hitch bushing (#3), hitch wear plate (#4),

tractor drawbar (#5), and washer (#6) as shown.

Secure with 1" locknut (#7). Tighten 1" locknut snugly

to remove all play and then back nut

one-quarter turn.

Do Not

torque 1" locknut.

2. Insert two 3/4" x 6" GR5 hex bolts (#8) through,

3/4" flat washers (#9), hitch top plate (#2), hitch wear

plate (#4), and formed hitch support (#10) as shown.

Secure with 3/4" locknuts (#11).

3. Tighten 3/4" locknuts to correct torque.
4. Remove 1" x 6 1/2" GR5 hex bolt (#12) and 1" lock

nut (#13) from hitch bushing (#3). Keep bolt and

locknut for reuse.

Attach Bar-Tite Hitch to Rotary Cutter

Refer to Figure 1-11:

DANGER

To avoid serious injury or death: A crushing hazard exists

while hooking-up and unhooking the implement. Keep people

and animals away while backing-up to the implement or

pulling away from the implement. Do not operate hydraulic

controls while a person or animal is directly behind the power

machine or near the implement.

WARNING

To avoid serious injury or death: The ball detent pin must be

fully inserted into the park jack with ball visible and popped

out on the far side of the jack before working on or around an

unhooked cutter.

Bar-Tite Hitch Assembly to Tractor Tongue

Figure 1-12

1. Make certain park jack (#3) is properly attached to

the cutter hitch and secured with detent pin (#8). If

park jack is not vertical, refer to

“Park Jack Angle

Alignment”

on page 29.

2. Store center 3-point link in its storage hook.
3. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

4. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 15.

5. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 13.

6. Raise or lower park jack (#3) to align hitch (#10) with

bolt hole in swivel clevis (#9).

22265

Bar-Tite Hitch Hook-up

Figure 1-11

37298

70461

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды