Land Pride RCG3715 Скачать руководство пользователя

Страница: 53 / 66

Section 5: Maintenance & Lubrication

RC(M)3715 & RCG(M)3715 Rotary Cutters 334-114M

1/26/21

Table of Contents

70478

Lubrication Points

Axle Hub Bearing

Type of Lubrication: Multi-Purpose Grease
Grease wheel bearings every 150 hours.

1-zerk per wheel (zerk can be on either side)

Quantity = 2 pumps
Repack wheel bearings annually

Adjustable Turnbuckle

Type of Lubrication: Multi-Purpose Grease
Grease both left & right hand side turnbuckles
Quantity = As required
Grease with wings folded up to remove pressure on

turnbuckle and allow grease to reach more areas.

Park Jack

1 - zerk
Type of Lubrication: Multi-purpose Grease
Quantity = As required

Frequency = As needed and when unhooking for
longterm storage.

hrs

Multi-purpose

spray lube

Multi-purpose

grease lube

Multi-purpose

oil lube

Intervals in hours at which

lubrication is required

Lubrication

Legend

70515

37725

Hours

150

Hours

Repack

Annually

Needed

Содержание RCG3715



































































Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды

Land Pride RCG3715, Руководство оператора

Результаты поиска

Содержание RCG3715

Отзывы:

Похожие инструкции для RCG3715

Бренды по названию

Популярные бренды