Land Pride RC4710 Скачать руководство пользователя страница 43

Страница: 43 / 72

Section 4: Options & Accessories

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Safety Chain Guards

DANGER

To prevent serious injury or death:
Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front & rear safety guards is

mandatory with this cutter. Double row chain guards should

be used when cutting along roadways and in areas where

people may be present. Stop blade rotation if bystanders are in

or around the area. It is recommended that a safety shield be

placed between the operator and cutter on an open air tractor.

Land Pride offers two types of safety guards to best suit

your application: single row chain guards and double row

chain guards.

•

Single row chain guards are constructed with a single

row of hanging chain links.

•

Double row chain guards are constructed with two

rows of hanging chain links. The extra chain provides

an additional barrier for stopping thrown objects.

RC(M) Models

334-839A . . . . . . . . . . . . . . Single Row Chain Guards
334-840A . . . . . . . . . . . . . Double Row Chain Guards

RCL(M) Models

334-841A . . . . . . . . . . . . . . Single Row Chain Guards
334-842A . . . . . . . . . . . . . Double Row Chain Guards

Hitches

Land Pride offers 5 different hitches to best suit your

application. See

“Hitch Types”

on page 13 for complete

description of optional hitches.

334-744A . . . . . . . . . . . . . . . . . . . Swivel Clevis Hitch
334-460A . . . . . . . . . . . . . . . . . . . . . . . Bar-Tite Hitch
334-462A . . . . . . . . . . . . . . . . . . . . . . . . . . .Ball Hitch
334-470A . . . . . . . . . . . . . . . . . . . . . . . . . Pintle Hitch
334-471A . . . . . . . . . . . . . . . . . LP Performance Hitch

Deck Protection Options

•

No protection:

The decks are standard construction

without additional protection added to their underside

such as the Deck Ring or Deck Armor

•

Deck Ring:

Land Pride offers a deck ring option for

extra protection for the deck sheet and structure. The

deck rings are welded to the underside of the center

deck and wing decks to protect from bent and deflected

blades caused by hitting obstructions.

Wing Fold Options

Land Pride offers two wing folding options to best suit

your application. The dual-acting cylinder has a narrower

transport width in comparison to the single-acting

cylinder.

•

Single-acting:

Raises and lowers the wing with single-

acting cylinder. Relies on gravity to pull wing to ground.

Uses 1 hydraulic duplex.

•

Dual-acting:

Simultaneously raise and lowers the

wing with dual-acting cylinder. Hydraulically power

wing up and down. Uses 1 hydraulic duplex.

RC(M) Models

331-789A . . . . . . . . . . . .Single-Acting Fold Assembly
331-790A . . . . . . . . . . . . . Dual-Acting Fold Assembly

RCL(M) Models

334-814A . . . . . . . . . . . .Single-Acting Fold Assembly
334-815A . . . . . . . . . . . . . Dual-Acting Fold Assembly

Tire Options & Configurations

Land Pride offers five different tire options to choose from,

with each option available in a 5 or 6 tire configuration.

•

Laminated Tires

: Available sizes are 21" and 26"

tires. They are constructed of laminated layers of solid

rubber that will never go flat.

•

New Tires

: 25.5", 20 ply tires are available as foam

and air-filled. Both are built tough to withstand the

rugged use a cutter receives, as well as providing a

smoother ride when transporting. Foam-filled tires will

not go flat.

•

Used Aircraft Tires

: Available as a 29" pneumatic tire

or 24" foam-filled tire. They are built tough to withstand

the rugged use a cutter receives and to provide a

smoother ride when transporting.

•

5 Tire Configuration:

Four tires on transport axle and

one on the wing axle.

•

6 Tire Configuration:

Four tires on transport axle and

two on the wing axle.

Section 4: Options & Accessories

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды