Land Pride RC4710 Скачать руководство пользователя страница 21

Страница: 21 / 72

Section 1: Assembly & Set-up

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

LP Performance Hitch Hook-up

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the

implement. Keep people and animals away while backing-up to

the implement or pulling away from the implement. Do not

operate hydraulic controls while a person or animal is directly

behind the power machine or near the implement.

WARNING

To avoid serious injury or death:
The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

Refer to Figure 1-10:

1. Make certain park jack (#3) is properly attached to the

cutter hitch and secured with ball detent pin (#8).

2. Adjust park jack angle if it is not vertical. Refer to

“Park Jack Angle Alignment”

on page 29

3. In order to properly align and hook-up the tractor’s

drawbar to the LP Performance Hitch, clevis opening

should be parallel with the drawbar. This can be

accomplished by rotating clevis (#9) so that the flip

hitch holder (#11) is positioned on top as shown.

Insert the customer supplied hitch pin (#1) through

holes in flip hitch holder (#11) as shown. Secure with

hairpin cotter (#2).

4. Remove bushings in clevis (#9) if customer supplied

hitch pin diameter is larger than 1". See

“LP

Performance Hitch Hole Size”

on page 31 for

instructions.

5. Store center 3-point link in the tractor’s storage hook.

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

customer supplied.

6. Start tractor, raise 3-point arms fully up, and carefully

back tractor within close proximity of clevis (#9).

Shut tractor down properly before dismounting

according to

“Tractor Shutdown Procedure”

page 15.

8. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

dimensions on page 13.

9. Raise or lower park jack (#3) to align clevis (#9) with

tractor drawbar. Drawbar should fit between lower

and upper plates of clevis.

10. Restart tractor and continue to back tractor up to

cutter hitch until holes in tractor drawbar and clevis

hitch (#9) are aligned.

11. Shut tractor down properly before dismounting.
12. Remove hairpin cotter (#2) and hitch pin (#1) from

hitch holder (#11) and rotate hitch holder down.

13. Attach cutter to tractor drawbar with hitch pin (#1) and

hairpin cotter (#2) as shown.

14. Lower park jack (#3) until hitch weight is supported

by tractor drawbar.

15. Relocate park jack (#3) from hitch frame to storage

base and secure with detent pin (#8). Ensure base of

park jack is level with, or lower than the jack crank

head. See cover picture for correct positioning.

16. Attach hitch safety chain (#4) to the tractor. Adjust

chain length to remove all slack except what is

necessary to permit turning. Lock chain hook

securely to the safety chain.

17. Continue with

“Hydraulic Hook-up”

on page 19.

IMPORTANT:

Before moving the cutter, relocate

park jack to the storage base located on the left wing

or weight box. Make sure jack is stored with its base

level or lower than the head to prevent water and

freeze damage.

LP Performance Hitch Hook-up

Figure 1-10

37298

72469

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды