Land Pride RC4710 Скачать руководство пользователя страница 32

Страница: 32 / 72

Section 1: Assembly & Set-up

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Refer to Figure 1-35:

13. Remove park jack (#3) from cutters top left side

storage base and attach to jack mount (#15) as

shown. Fully insert detent pin (#8) in jack mount

(#15) to secure park jack (#3).

14. If needed, realign park jack (#3) to be vertical. Refer

“Park Jack Angle Alignment”

on page 29.

15. Unhook hitch safety chain (#4) from tractor.
16. Unhook hydraulic hoses (#7) from tractor duplex

outlets. Insert couplers through hole (A) on the hitch

frame and slide them down the slot as shown to keep

couplers out of the dirt. See

Figure 1-34

on page 27.

17. Unhook wire harness (#13) from tractor outlet. Insert

wire harness through hole (B) on the hitch frame with

connector hanging down to keep moisture out.

See

Figure 1-34

on page 27.

18. Rotate driveline hanger (#16) up to position shown.
19. Pull back on locking collar (#6) and pull driveline (#5)

from tractor power take-off shaft.

20. Collapse driveline (#5) by pushing tractor end of

driveline toward the splitter gearbox. Store driveline

on hanger (#16).

21. Adjust park jack (#3) as needed to raise cutter hitch

off the tractor drawbar.

22. Remove connecting hitch pin or bolt as follows:

For LP Performance Hitch, See

Figure 1-35:

Remove hairpin cotter (#2) and hitch pin (#1).

For Swivel Clevis Hitch, See

Figure 1-36:

Remove hairpin cotter (#2) and hitch pin (#1).

For Bar-Tite Hitch, See

Figure 1-37:

Remove locknut (#1) and bolt (#2).

23. Restart tractor and slowly drive tractor forward

several feet.

24. Shut tractor down properly before dismounting

according to

“Tractor Shutdown Procedure”

page 15.

25. Lower park jack until cutter is resting on its front skid

shoes.

26. Replace connecting pin/bolt as follows:

For LP Performance Hitch, See Figure 1-35:

Rotate clevis (#9) horizontal and flip hitch holder

(#11) up so that its holes are on top as shown.

Insert hitch pin (#1) through holes in hitch holder

(#11). Secure with hairpin cotter (#2).

For Swivel Clevis Hitch, See

Figure 1-36:

Replace connecting pin (#1) in clevis (#9) and

secure with hairpin cotter (#2).

For Bar-Tite Hitch, See

Figure 1-37:

Insert bolt (#2) through hitch (#9) and screw lock

nut (#4) onto bolt (#2) with several turns.

Unhook LP Performance Hitch

Figure 1-35

Unhook Swivel Clevis Hitch

Figure 1-36

Unhook Bar-Tite Hitch

Figure 1-37

72469

72471

70461

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды