Land Pride RC4710 Скачать руководство пользователя страница 44

Страница: 44 / 72

Section 4: Options & Accessories

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Axle Options and Configurations

Land Pride offers a multitude of axle options to ensure

your Rotary Cutter is properly fitted for its intended

application. Purchaser must choose one center axle

option and one wing option.

Single Suspension Center and Wing Axles

Refer to Figure 4-1:

This center and wing axle option provides suspension

through the use of two springs located directly behind the

center deck’s lift cylinder. It is best suited for relatively flat

and even terrain.

Center Axle Options
HD Single Suspension Center Axle

Refer to Figure 4-2:

This heavy duty (HD) center axle option provides

suspension through the use of two springs located

directly behind the center deck’s lift cylinder. The HD

axles features bigger tubing and large gussets, making it

a great option when the cutters main application goes

just beyond flat and even terrain. This option allows the

purchaser to choose a separate wing axle option that

meets their needs.

Independent Suspension Center Axle

Refer to Figure 4-3:

Not applicable with

“HD Rigid Wing Axle”

on page 41.

This HD center axle option provides independent

suspension. Each trailing arm features a rocker and

spring to better handle rough terrain. When field terrains

are less than ideal, and additional suspension support is

needed, this center axle option will easily meet those

expectations.

Walking Tandem Center Axle

Refer to Figure 4-4:

The walking tandem axle features a beam on each

trailing arm that pivots front to back. The beam pivots in

the center with a spindle in front and a spindle in back of

the pivot. This axle is great for walking through washouts

or on/off curbs.

Pivot Parallel Center Axle

Refer to Figure 4-5:

The parallel pivot axle features a beam on each trailing

arm that pivots side to side. The side to side pivoting

action spreads the weight evenly between the wheel. This

axle is great for holding slopes while minimizing tire wear.

Figure 4-1

Figure 4-2

Figure 4-3

Figure 4-4

Figure 4-5

72476

SMV Mounting Socket

72478

72479

72480

72481

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды