Land Pride RC4710 Скачать руководство пользователя страница 20

Страница: 20 / 72

Section 1: Assembly & Set-up

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Swivel Clevis Hitch Hook-up

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the

implement. Keep people and animals away while backing-up

to the implement or pulling away from the implement. Do not

operate hydraulic controls while a person or animal is directly

behind the power machine or near the implement.

WARNING

To avoid serious injury or death:
The ball detent pin must be fully inserted into the park jack

with ball visible and popped out on the far side of the jack

before working on or around an unhooked cutter.

Refer to Figure 1-9:

1. Make certain park jack (#3) is properly attached to

the cutter hitch and secured with detent pin (#8). If

park jack is not vertical, refer to

“Park Jack Angle

Alignment”

on page 29.

2. Store tractor’s center 3-point link in its storage hook.
3. Start tractor and raise 3-point arms fully up.
4. Carefully back tractor to close proximity of clevis (#9).
5. Shut tractor down properly before dismounting

according to

“Tractor Shutdown Procedure”

page 15.

6. Verify tractor drawbar is adjusted correctly. Refer to

“Drawbar Set-up”

on page 13.

Raise or lower park jack (#3) to align clevis (#9) with

tractor drawbar. Drawbar should fit between lower

and upper plates of clevis.

8. Restart tractor and continue to back tractor up to

cutter hitch until hitch holes in tractor drawbar and

clevis (#9) are aligned.

9. Shut tractor down properly before dismounting.

10. Attach cutter to tractor drawbar with customer

supplied hitch pin (#1) and hairpin cotter (#2).

11. Lower park jack (#3) until hitch weight is supported

by drawbar.

12. Relocate park jack (#3) from hitch frame to storage

base and secure with detent pin (#8). Ensure base of

park jack is level with, or lower than the jack crank

head. See cover picture for correct positioning.

13. Attach hitch safety chain (#4) to the tractor. Adjust

chain length to remove all slack except what is

necessary to permit turning. Lock chain hook

securely to the safety chain.

14. Continue with

“Hydraulic Hook-up”

on page 19.

NOTE:

Hitch pin (#1) and hairpin cotter (#2) are

supplied by customer.

IMPORTANT:

Before moving the cutter, relocate park

jack to the storage base located on the left wing or

weight box. Make sure jack is stored with its base level

or lower than the head to prevent water and freeze

damage.

Swivel Clevis Hitch Hook-Up

Figure 1-9

37298

72196

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды