Land Pride RC4710 Скачать руководство пользователя

Страница: 50 / 72

Section 5: Maintenance & Lubrication

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Drivelines

Before each use, check that all driveline shields and

drivelines are in place, undamaged and in working order.

Replace shields and drivelines as needed. Order only

genuine Land Pride parts from your local Land Pride

dealer.

DANGER

To prevent serious injury or death:
Tractor power take-off shaft shield, driveline shields, and

gearbox shaft shields must be installed and in good working

condition to avoid driveline entanglement and projectiles

flying off of the driveline.

WARNING

To prevent serious injury or death:
Do not operate a broken or bent driveline. Such a driveline

will break apart while rotating at high speeds and can cause

serious injury or death. Always remove the implement from

use until the damaged driveline can be repaired or replaced.

Drivelines With Slip Clutches

Friction clutches must be capable of slippage during

operation to protect gearboxes, drivelines, and other

drive train parts. Friction clutches should be “run-in” prior

to initial operation and after periods of inactivity to

remove any oxidation from the friction surfaces. Repeat

“run-in” at the beginning of each season and when

moisture seizes the inner friction plates.

WARNING

To avoid serious injury or death:

•

Always follow “Tractor Shutdown Procedure” provided in

this manual before dismounting the tractor.

•

A slip clutch that has been in use or has slipped for as little

as only two or three seconds during run-in may be too hot

to touch. Allow a hot clutch to cool before working on it.

Clutch Run-in

Refer to

Figure 5-6:

1. Using a pencil or other marker, scribe a line across the

exposed edges of the clutch plates and friction disks.

2. Carefully loosen each of the 8 spring retainer nuts by

exactly two revolutions. It will be necessary to hold

the hex end of the retainer bolt in order to

count the

exact number of revolutions

3. Make sure the area is clear of all bystanders and

machine is safe to operate.

IMPORTANT:

Prior to initial operation and after 30

days of inactivity, slip friction disks to remove

oxidation and moisture. Moisture allows disks to slip

easily. Oxidation can prevent disk from slipping

causing driveline damage. This damage is NOT

covered under the warranty.

4. Start tractor and engage power take-off drive for 2-3

seconds to permit slippage of the clutch surfaces.

Disengage power take-off, then re-engage a second

time for 2-3 seconds. Disengage power take-off, shut

off tractor, and remove key. Wait for all components to

stop before dismounting from tractor.

5. Inspect clutch and ensure that the scribed markings

made on the clutch plates have changed position.

Slippage has not occurred if any two marks on the

friction disk and plate are still aligned. A clutch that

has not slipped must be disassembled to separate

the friction disk plates. See

“Clutch Disassembly,

Inspection & Assembly”

below.

6. Tighten each of the 8 spring retainer nuts on the

clutch housing exactly two revolutions to restore

clutch to original setting pressure.

Allow clutch to cool to ambient temperature before

operating again. Clutch is now ready for use.

8. The clutch should be checked during the first hour of

cutting and periodically each week. An additional set

of scribe marks can be added to check for slippage.

See

Figure 5-7

on page 47 to adjust spring length.

Clutch Run-In

Figure 5-6

Clutch Disassembly, Inspection &

Assembly

Refer to Figure 5-8:

If the clutch run-in procedure performed above indicated

that one or more friction disks did not slip, then the clutch

must be disassembled to separate the friction disks.

Disassembly

Disassembly of clutch is simply a matter of first removing

spring retainer nuts (#1), springs (#2), and bolts (#3) from

the assembly. Each friction disk (#4) must then be

separated from the metal surface adjacent to it.

13693

IMPORTANT:

Not all clutches are assembled the

same with the same number of components. Be sure

to keep track of order and orientation of your clutch

components during disassembly.

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды