Land Pride RC4710 Скачать руководство пользователя страница 29

Страница: 29 / 72

Section 1: Assembly & Set-up

RC(L)4710 & RCM(L)4710 Rotary Cutters 334-863M

7/31/20

Table of Contents

Purge Hydraulic System

DANGER

To prevent serious injury or death:
Never remove or install a folding wing cylinder with cylinder

rod retracted and wing folded-up. The wing is unstable without

its folding cylinder and can suddenly fall. Also, air trapped in

a new or repaired cylinder will drop the wing suddenly when

lowering the wing. Either situation can render the cutter

inoperable and cause serious bodily injury or death.

WARNING

To prevent serious injury or death:
Be sure center and wing deck are lowered to the ground and all

hydraulic pressure is relieved before loosening any hydraulic

lines or fittings to purge the hydraulic system.

Wing Fold Cylinder

Refer to Figure 1-26:

1. Lower center deck until it is supported by stroke

control flip spacers (#5) on hydraulic cylinder (#3).

2. Lower wing deck until deck is resting on the ground.
3. Shut tractor down properly before dismounting

according to

“Tractor Shutdown Procedure”

on page

15. Now move tractor control levers back and forth to

relieve all hydraulic pressure.

4. Slightly loosen hydraulic hose fitting (#2) on wing

cylinder (#1) to allow air to escape.

5. Restart tractor and slowly activate tractor control lever

to retract wing cylinder (#1), and to purge trapped air

from the hydraulic system.

6. Once all air has been purged from hydraulic system,

properly shutdown tractor once more.

Retighten hose fitting (#2) on wing cylinder (#1).

Deck Lift Cylinder

Refer to Figure 1-26:

1. Move all hydraulic stroke control flip spacers (#5) to

open position, then proceed to lower center deck.

2. Shut tractor down properly before dismounting

according to

“Tractor Shutdown Procedure”

page 15. Now move tractor control levers back and

forth to relieve all hydraulic pressure.

3. Slightly loosen hydraulic hose fitting (#4) on deck lift

cylinder (#3) to allow air to escape.

4. Restart tractor and slowly activate tractor control lift

lever to extend lift cylinder (#3) and to purge trapped

air from the hydraulic system.

5. Now, shut tractor down properly again.
6. Retighten hose fitting (#4) on lift cylinder (#3).

Purge Wing & Center Deck Cylinders

Figure 1-26

72467

Содержание RC4710









































































Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды

Land Pride RC4710, Руководство оператора

Результаты поиска

Содержание RC4710

Отзывы:

Похожие инструкции для RC4710

Бренды по названию

Популярные бренды