manualshive.com logo in svg

LANCIER Monitoring ACS 10000, Руководство по эксплуатации

Поделиться
Скачать
LANCIER Monitoring ACS 10000 Скачать руководство пользователя страница 6

Page 6

General Information

These operating instructions should make it easier for you to become acquaint-
ed with the product. They contain important information to ensure safe, appro-
priate and cost-effective use of the equipment.

The operating instructions endorse the directives of national regulations for the
prevention of accidents and the protection of the environment. 

These operating instructions shall be read and adopted by anyone
assigned to work with/on the equipment, e. g. during operation to 
include setting-up, maintenance trouble-shooting.

In addition to the operating instructions and the mandatory regulations for the
prevention of accidents, applicable in the operator's country and at the place of
use, the recognized technical regulations for safe and professional operation
shall also be observed.

Designated Use

The ACS addressable compressor monitoring unit enables assessment of the
operational status of stationary pressurization equipment by measuring physical
parameters that are based on defined technical data (see pp. 4 and 5).

Any non-compliant use excludes the manufacturer from liability for any dam-
ages. The operator carries the risk!

Safety Instructions

Important!
Read and observe safety instructions prior to initial operation!

• Keep the operating instructions ready to hand!

Accident prevention!
Before opening the housing, make sure that the operating current 
and lines being monitored are switched off!

• The device should only be operated in technically-sound condition, for its

designated use, with safety and risk awareness in mind, taking into account
the operating instructions! 

Содержание ACS 10000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды