manualshive.com logo in svg

LANCIER Monitoring ACS 10000, Руководство по эксплуатации

Поделиться
Скачать
LANCIER Monitoring ACS 10000 Скачать руководство пользователя страница 3

ACS addressable compressor monitoring unit

with display and control panel

ACS 5000: 

total air flow 0 ..   5000 l/h

Order-no. 072891.010

ACS 10000: 

total air flow 0 .. 10000 l/h

Order-no. 072891.110

Accessories

Pressure sensor 0-10 bar

Order-no. 073153.000

Temperature sensor -20 to +80 °C, 

extern, 

for ambient temperature

Order-no. 073154.000

Temperature sensor -50 to +180 °C, 

extern, 

for compressor temperature

Order-no. 073155.100

Microfilter, 

for air input to protect sensors from dust

Order-no. 073206.000

Ordering Data

Page 3

Operate an MFR with the ACS   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Read out MFR Values  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Reset maintenance counter  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Show MFR Alarm Conditions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
MFR Alarm Display Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
MFR Alarm Display - deactivate humidity monitoring  . . . . . . . . . . . . . .23
Read out MFR Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Read out MFR Info   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Service mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Change ACS Settings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Change MFR Settings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Set up ACS Top Value   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Set up Air Flow Value   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Declaration of Conformity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Important!
It is imperative to read and observe all safety instructions prior to
initial operation!

© 2014 LANCIER Monitoring GmbH. 

This operating instruction must not be reproduced or made available, either com-
plete or in extracts, before the specific consent of LANCIER Monitoring GmbH.

Содержание ACS 10000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды