manualshive.com logo in svg

LANCIER Monitoring ACS 10000, Руководство по эксплуатации

Поделиться
Скачать
LANCIER Monitoring ACS 10000 Скачать руководство пользователя страница 21

Page 21

Read out ACS Info 

Menu selection:

Menu D1

>Disp.  Device  :    ACS

Press softkey „select“

Menu D2.1

>ACS  –  Info

Press softkey „select“

Display 

D3.3

„ACS - Info“ shows up:

Version, date and time of the ACS software and
the first address of the Tx-bus of the ACS are
indicated. The ACS uses ten addresses on the
Tx-bus (the one in the display and the nine fol-
lowing) to allocate all measured values explicit
into the LANCIER monitoring system.

Display Settings

Menu selection:

Menu D1

>Display  Settings

Press softkey „select“

Display 

D2.3

„Display Settings“ shows up:

Use softkeys (

A

) „up“ and „down“ to scroll to

the value to set: 

Brightness

= Brightness of the display

(value 0 - 15)

Timeout (min) = Period in minutes for shut-down

of display illumination when dis-
play is idle (value 0 - 250).

Press the softkey „select“ to chose the displayed value.

Use softkeys (

A

) „up“ and „down“ to increase or to reduce the value.

Press the softkey „set“ to store the displayed value.

Read out Display Info 

Menu selection:

Menu D1

>Display  Info       

Press softkey „select“

Display 

D2.4

„Display Info“ shows up:

Version, Date and Time of the display software
are indicated. 

ACS - Info

Software Vers. :V111
Date  : 21-Jun-06
Time  : 12:40:08
Tx-Adress     : 2

______________________

|

| back

Display  Settings

Brightness   :  10
Timeout[min] :  30

>back
______________________

up

|

down

| select

Display Info

Software Vers. :V101
Date  : 16-Jun-06
Time  : 12:40:08

______________________

|

| back

Содержание ACS 10000





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды