manualshive.com logo in svg
background image

8

ELECTRICAL WARNING/ADVERTENCIA ELÉCTRICA/

AVERTISSEMENT ÉLECTRIQUE

Check the dispenser serial number plate for correct electrical requirements of unit. Do not plug into a wall

electrical outlet unless the current shown on the  serial  number  plate  agrees  with  local  current  available. Follow 

all local electrical codes when making connections. Each dispenser must have  a  separate  electrical circuit. Do  not  

use  extension  cords  with  this  unit.  Do  not  ‘gang’  together  with  other  electrical  devices on the same outlet. The 

keyswitch does not disable the line voltage to the transformer primary. Always disconnect electrical power to the unit  

to  prevent  personal  injury  before  attempting  any  internal  maintenance. The resettable breaker switch should not 

be used as a substitute for unplugging the dispenser from the power source to service the unit. Only qualified 

personnel should service internal components of electrical control housing. Make sure that all water lines are tight 

and units are dry before making any electrical connections!

Verifique la placa con el número de serie del dispensador, donde encontrará los requisitos  eléctricos correctos 

de la unidad. No enchufe la unidad en un tomacorriente de pared a menos que la corriente indicada en la placa con 

el número de serie concuerde con la corriente local disponible.  Al hacer las conexiones, respete todos los códigos 

eléctricos locales. Cada dispensador debe tener un circuito eléctrico independiente. No use extensiones con esta 

unidad. No la conecte junto con otros dispositivos eléctricos al mismo tomacorriente. El interruptor de llave no corta 

el voltaje de línea al transformador primario desconecte siempre la alimentación eléctrica a la unidad para evitar 

lesiones personales  antes  de  tratar  de  realizar  tareas  de  mantenimiento.   El  disyuntor  de  sobrecarga  

reseteable no se debe usar como sustituto para desenchufar el dispensador de la fuente de alimentación para 

realizar tareas de servicio de la unidad. El servicio de los componentes internos de la caja de control eléctrico debe 

confiarse exclusivamente a personal calificado. Asegúrese de que todas las líneas de agua estén ajustadas y las 

unidades estén secas antes de hacer conexiones eléctricas.

Examinez la plaque de numéro de série du distributeur pour connaître les bonnes exigences en matière 

d’électricité pour l’appareil. Ne le branchez pas à une prise électrique murale à moins que le courant indiqué sur la 

plaque de numéro de série corresponde au courant local disponible. Respectez tous les codes électriques locaux 

lorsque vous faites des  connexions.  Chaque  distributrice  doit  avoir  un  circuit  électrique  séparé.  N’utilisez  pas 

de cordons prolongateurs avec cet appareil. Ne pas le brancher avec d’autres appareils électriques sur la même 

prise. L’interrupteur à clé ne coupe pas la tension secteur au transformateur primaire. Débranchez toujours le courant 

électrique à l’appareil, afin de prévenir des blessures, avant de faire un entretien interne quelconque. Le disjoncteur

réarmable ne devrait pas être utilisé au lieu de débrancher le distributeur de la source d’alimentation en électricité 

pour faire de l’entretien/une réparation de l’appareil. Seul le personnel qualifié devrait faire l’entretien/la réparation 

des composants internes dans le logement des commandes électriques. Assurez-vous que toutes les conduites 

d’eau sont étanches et que les appareils sont secs avant de faire des connexions électriques!

F

F

CO2/CARBON DIOXIDE /El ANHÍDRIDO CARBÓNICO/

DIOXYDE DE CARBONE

Carbon Dioxide (CO2) is a colorless, noncombustible gas with a light pungent odor. High percentages of CO2 may 

displace oxygen in the blood. Prolonged exposure to CO2 can be harmful. Personnel exposed to high concentrations 

of CO2 gas will experience tremors which are followed by a loss of consciousness and suffocation. If a CO2 gas leak 

is suspected, immediately ventilate the contaminated area before attempting to repair the leak. Strict attention must 

be observed in the prevention of CO2 gas leaks in the entire CO2 and soft drink system.

El anhídrido carbónico (CO2) es un gas incoloro, no combustible, con un olor pungente ligero. Altos porcentajes 

de CO2 en la sangre pueden desplazar el oxígeno en la sangre. La exposición prolongada al CO2 puede ser nociva. 

El personal expuesto a concentraciones altas de CO2 sufre temblores seguidos de la pérdida de la consciencia y 

sofocación. Si se sospecha que existe una pérdida de CO2, ventile el área contaminada antes de tratar de reparar 

la pérdida. Hay que prestar suma atención para evitar pérdidas de CO2 en todo el sistema de CO2 y de bebidas 

gaseosas.

 

Le dioxyde de carbone (CO2) est plus lourd que l’air et déplace l'oxygène. Le CO2 est un gaz incolore et 

incombustible, ayant une odeur un peu âcre. Des concentrations fortes de CO2 peuvent déplacer l'oxygène dans le 

sang. Une exposition prolongée au CO2 peut être nocive. Le personnel exposé à de fortes concentrations de CO2 

gazeux éprouvera des tremblements, suivis rapidement d'une perte de conscience et de suffocation. On doit faire très 

attention de prévenir les fuites de CO2 gazeux dans le système entier de CO2 et de boisson gazeuse. Si on suspecte 

qu'il y a une fuite de CO2 gazeux, aérez le secteur contaminé immédiatement avant d'essayer de réparer la fuite.

5

5

Содержание 605





































Отзывы: