Lamborghini Caloreclima TITAN 150, Инструкция по использованию, установке и обслуживанию

Страница: 116 / 144

TITAN
116
EN
cod. 3541Z410 - Rev 01 - 09/2022
Parameters Menu - Transparent Parameters
31 parameters are available, indicated by the letter “P” , which are not modifiable from Remote Timer Control.
Table 5-Parameters - Transparent
Notes
1. Parameters with more than one description vary their function and/or range in relation to the setting of the parameter
given in brackets.
2. Parameters with more than one description are reset to the default value if the parameter given in brackets is mo-
dified.
3. The Maximum Heating Power parameter can also be modified in Test Mode.
Parameter Description Range
P01 Ignition power 0-100% 30
P02 Heating ramp 1-10°C/minute 1
P03 Virtual setpoint min. temperature 20 ÷ 80°C 20
P04 Heating standby time 0 ÷ 10 minutes 4
P05 Heating Post-Circulation 0 ÷ 255 minutes 3
P06 Pump operation 0-3 Operation strategy 0
P07 Modulating pump min. speed 0 ÷ 100% 30
P08 Modulating pump start speed 0 ÷ 100% 75
P09 Modulating pump max. speed 30 ÷ 100% 100
P10 Pump deactivation temperature during Post-Circulation 0 ÷ 100°C 35
P11 Pump activation hysteresis temperature during Post-Circulation 0 ÷ 20°C 5
P12 Heating user min. setpoint 10 ÷ 90 °C 20
P13 Heating user max. setpoint 20 ÷ 90 °C 80
P14 Max. output in heating 0-100% 80
P15 DHW ramp 1-10°C/min 5
P16 DHW standby time 0-255 seconds 120
P17 DHW pump Post-Circulation 0-255 seconds 30
P18
With B02 = 7 - Not implemented -- --
With B02 = 8 - DHW user min. setpoint 10° ÷ 40° 10°
With B02 = 9 - DHW user min. setpoint 10° ÷ 40° 10°
P19
With B02 = 7 - Not implemented -- --
With B02 = 8 - DHW user max. setpoint 40° ÷ 70° 65°
With B02 = 9 - DHW user max. setpoint 40° ÷ 70° 65°
P20 Max. output in DHW 0-100% 80%
P21
With B02 = 7 - Not implemented -- --
With B02 = 8 - Hot water tank hysteresis 0° ÷ 60° 2°
With B02 = 9 - Hot water tank hysteresis 0° ÷ 60° 2°
P22
With B02 = 7 - Not implemented -- --
With B02 = 8 - Primary setpoint 70° ÷ 85° 80°
With B02 = 9 - Primary setpoint 70° ÷ 85° 80°
P23
With B02 = 7 - Not implemented -- --
With B02 = 8 - Legionella protection ON - OFF OFF
With B02 = 9 - Legionella protection ON - OFF OFF
P24 Fan frequency in standby mode 0-255 Hz 0
P25 Modulating pump adjustment temperature 0-60°C 20
P26 Primary exchanger protection temperature 0-80°C 35
P27 System min. pressure value -- --
P28 System nominal pressure value -- --
P29 Exchanger protection intervention
0 = No F43,
1-15 = 1-15°C/second
0
P30 Heating hysteresis after ignition 6-30°C 10
P31 Timer for heating hysteresis after ignition 0-180 seconds 60