Kyocera TASKalfa 3051ci страница 314 Скачать руководство пользователя

Страница: 314 / 317

2L6/2N6/2N5/2N4

1-4-313

1-4-12 Printing System Troubleshooting

(1) List of Erro Code

Problem/

Error code

Condition of

detection

Causes

Check procedures/ Corrective

measures

1.Error 1020 is dis-
played.

Error occurs during

Bridge Board mem-

ory check.

Bridge Board error.

Replace Bridge Board.

2.Error 1030 is dis-
played.

Timeout for
FieryReady signal
not received.

Printing system is not pow-
ered.

Check power cable connection or
replace.

DVI cable between Fiery
Print Controller and MFP is
disconnected.

Re-insert/replace DVI cable.

3.Error 1031 is dis-
played.

Receiving VIDEO
from Fiery fails.
(IP Exchange fail-
ure)

DVI cable between Fiery
Print Controller and MFP is
disconnected.

Re-insert/replace DVI cable.

Bridge board error.

Replace Bridge Board.

4.Error 1040 is dis-
played.

LINKLOCAL con-
nection fails.

Network cable between
Fiery Print Controller and
MFP is disconnected.

Re-insert/replace network cable.

Network setting failure.

Check network settings.
  IPv6:  ON
  HTTP:  ON
  EnhancedWSD:  ON

5.Error 2000 is dis-
played.

Mismatch of Pro-
ductID from Fiery.

Unsupported Fiery Print
Controller is installed.

Install supported Fiery Print Con-
troller. (Use with correct combi-
nation)

FW version of Main Con-
troller and Fiery Print Con-
troller version do not match.

Check FW version and update
FW.

6.Error 2010 is dis-
played.

CometFPGA ver-
sion mismatch.

Unsupported Bridge Board
is installed.

Replace Bridge Board.

7.Error 2020 is dis-
played.

FW version mis-
match.

FW version of Main Con-
troller and Fiery Print Con-
troller does not match.

Check FW version and update
FW.

8.Error 3000 is dis-
played.

Timeout of ERPD
Server boot-up of
External RIP Proto-
col.

Bad data in IP Exchange.

Turn on MFP power again.

Replace Bridge Board.

Replace Main Board.

Replace Fiery Print Controller.

Содержание TASKalfa 3051ci






























































































































































































































































































































Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды

Kyocera TASKalfa 3051ci, Руководство по обслуживанию

Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды