Kyocera TASKalfa 3051ci страница 222 Скачать руководство пользователя

Страница: 222 / 317

2L6/2N6/2N5/2N4

1-4-221

3. DP-scanning second (back) page (with a dual scan DP installed)

4. DP-scanning second (back) page (with a reversed DP installed)

Defective part

Check description

Corrective Action

White-reference
roller (Counter the
CIS)

Check if the white reference
roller is contaminated on its sur-
face or damaged.

If the white-reference roller is dirty, clean. Or, if
the roller is damaged, replace.

DP_CIS glass

Check whether the CIS glass is
contaminated.

If the CIS glass is contaminated, clean the CIS
glass and conveying guide. If it has a scuff,
replace.

White streaks com-
pensation settings

Check the white streaks com-
pensation settings.

If the white streaks compensation is
insufficient, perform maintenance mode U091.

DP_CIS unit

Check the location the CIS unit
is mounted.

Re-mount the CIS unit if it is hanged off.

DP_SHD PWB

Check the CIS and the SHD
PWB is properly connected.

Reinsert the connector if the PWB was loosely
inserted.If not cured, replace the PWB.

DP_CIS

CIS is defective.

Replace the CIS and perform U091 and U411.
(see page 1-3-71,1-3-173)

Main PWB

The main PWB is defective.

Replace the main PWB.(see page 1-5-72)

Defective part

Check description

Corrective Action

Original document

Check whether the original

document is dirty.

If the original document is dirty, replace.

Contact glass

Check whether the contact glass
is dirty.

If the contact glass is dirty, clean the contact
glass, and the bottom part of the shading plate.

Mirror

Check whether the mirrors are
dirty.

If the mirrors are dirty, clean the three mirrors.

Lamp unit

Check that the lamp unit is con-
taminated with dusts.

If dusts are observed on the lamp unit, remove
the dusts in the light paths.

Lamp unit

Check whether the LED cover is
hanged off.

Re-mount the LED cover if it is hanged off.

ISU

Check whether the lens cover is
hanged off.

Re-mount the lens cover if it is hanged off.

Shading plate

Check whether the shading plate
is dirty.

If the shading plate is dirty, perform
maintenance mode U063 to modify the
shading position. If it does not cure, replace the
contact glass assembly.
(see page 1-3-55)

ISC PWB

The ISC PWB is defective.

Replace the ISC and perform U411.

(see page 1-3-173)

Содержание TASKalfa 3051ci






























































































































































































































































































































Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды

Kyocera TASKalfa 3051ci, Руководство по обслуживанию

Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды