Kyocera TASKalfa 3051ci страница 100 Скачать руководство пользователя

Страница: 100 / 317

2L6/2N6/2N5/2N4-4

1-4-99

2760

Transfer motor startup error

Transfer motor is not stabi-
lized within 5 s since the
motor is activated.

Transfer motor

1. To check the motor operation, execute

U030 Belt Meand (see page 1-3-34).

2. Rotate the drive gear, the belt and the

roller by the hand and check that they
are not unusually loaded.

3. Clean the Intermediate transfer belt unit.
4. Confirm that the wiring connector is

firmly connected and, if necessary,
connect the connector all the way in.
Transfer motor and Feed PWB 1 (YC13)
Feed PWB 1(YC2) and Engine PWB
(YC5)

5. If the wiring is disconnected, shorted or

grounded, replace the wiring.

6. Replace the Transfer motor.

Feed PWB 1

Replace the Feed PWB 1.

Engine PWB

1. Check the engine software and upgrade

to the latest, if necessary.

2. Replace the engine PWB (see page 1-5-

80).

2770

Intermediate transfer belt
meandering correction
error

If the intermediate transfer
belt position detecting sensor
has derived an incorrect
value.

Intermediate trans-
fer belt unit

1. Check that the Intermediate transfer belt

unit has been properly installed so that
the intermediate belt unit waste toner

unit is strongly inserted.

2. Reinstall the intermediate transfer belt

unit.(Insert slowly all the way in.

3. Run U469 Belt Position with B/W and

within the range (6 to 26) (see page 1-3-
204).

4. Check that the main unit is placed

perfectly horizontal.

5. Replace the intermediate transfer belt

unit (see page 1-5-62).

Transfer belt
sensor (Intermedi-
ate transfer belt
unit)

1. Clean the toner off of the sensor and its

proximity using a blower.

2. Check the sensor actuator are correctly

positioned.

Engine PWB

1. Check the engine software and upgrade

to the latest, if necessary.

2. Replace the engine PWB (see page 1-5-

80).

Code

Contents

Related parts

Check procedures/

corrective measures

Содержание TASKalfa 3051ci






























































































































































































































































































































Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды

Kyocera TASKalfa 3051ci, Руководство по обслуживанию

Результаты поиска

Содержание TASKalfa 3051ci

Отзывы:

Похожие инструкции для TASKalfa 3051ci

Бренды по названию

Популярные бренды