Kverneland 2620M Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 47

background image

15

Preparation

Preparation

Position lifting bolts position B

•

The linkage pins below must
be used for attachment:

•

The width of the tractor is
measured from the outside
edge of the tires as shown.

•

Position B

Assembly - attachment

Preparation

Preparation

Attachment

Attachment

•

Activate the tractor's lift arms
and lift the machine free of the
ground.

•

Turn the support leg around
and raise it up as shown.

•

Mount the machine onto the
tractor's lift arms.

•

Selecting the position of the
top link:

TIP! It is recommended that the
top link is parallel to the tractor's
lift arms.

Position lifting bolts position A

«
...
13
14
15
16
17
...
»

Содержание 2620M
















































Отзывы:

Нет отзывов

Похожие инструкции для 2620M

Бренд: Hagie Страницы: 61

Бренд: JackJaw Страницы: 2

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Haigh Страницы: 60

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Water Witch Страницы: 2

Бренд: Falltech Страницы: 48

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренд: Olsen Страницы: 58

Бренд: Qlight Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды