Kverneland 2620M Скачать руководство пользователя страница 40

Страница: 40 / 47

Maintenance

Alignment discs

Wearing soles/skids

•

Inspect the timing of the discs.
Out of timing could be caused
by an impact of foreign
objects. If so, please check
the key in the hub.

•

Carry out a visual inspection
of the machine's stone guard
and counter knife for wear
with the cutting unit in the
headland position.

•

Stone guards and counter
knives with visible holes
caused by heavy wear must
be replaced immediately.

Note;

Stone guards are the same for

all models but not the counter
knives as the distance between the
hubs is not the same for all
models.

How to check alignment discs

How to check wearing of soles

•

Every season;

remove the top

cover on the cone.

•

Clean any dirt from inside the
cone.

•

Fit the top cover on the cone.

Internal inspection drum

Drum

Quick fit

•

If the machine is fitted with
knife quick release*, the same
requirement applies for bolt
wear and torque.

Wearing quick fit

Содержание 2620M
















































Результаты поиска

Содержание 2620M

Отзывы:

Похожие инструкции для 2620M

Бренды по названию

Популярные бренды

Kverneland 2620M, Руководство пользователя

Результаты поиска

Содержание 2620M

Отзывы:

Похожие инструкции для 2620M

Бренды по названию

Популярные бренды