KUHN PZ280F Скачать руководство пользователя страница 54

Страница: 54 / 75

Maintenance

General

At all maintenance tasks, secure the machine in the operating
position. In case the transport position is required, this is mentioned
separately.

Directions

Direction specifications (left, right, front, rear) are always meant in
relation to direction of travel.

Maintenance terms

In the table below you will find some short explanations of the most
common maintenance tasks.

Lubricants

specifications

Direction

Description

Left

Counterclockwise

Right

Clockwise

Rotation around a horizontal axis

As seen at right angles to the direction of travel from left to right

Rotation around a vertical axis

As seen from top to bottom

Task

Explanation

Grease

Apply grease to the sliding surface by using a brush

Lubricate

One or two presses with a grease gun, unless stated otherwise.

Oil

Apply an oil film (to the sliding face).

Replenish

Fill up fluids, oil or lubricants to the indicated maximum level.

Replace

Remove a part and install a new part. Drain fluids, oils or lubricants
and replenish to the indicated maximum level.

Check

Check the condition of parts and components, and replace if
necessary. Check the levels of all fluids, oils and lubricants,
replenish to the indicated maximum level if necessary.

Lubricant

Specifications

Oil

Class NLGI2, K2k in accordance with DIN51825

Gearbox Oil

SAE 85W-90 API GL-5

Grease

Multipurpose, grade EP 2

Содержание PZ280F












































































Результаты поиска

Содержание PZ280F

Отзывы:

Похожие инструкции для PZ280F

Бренды по названию

Популярные бренды

KUHN PZ280F, Руководство по эксплуатации

Результаты поиска

Содержание PZ280F

Отзывы:

Похожие инструкции для PZ280F

Бренды по названию

Популярные бренды